Is there any project implemented in INDIA using Basalt Fibre Reinforced Polymer(BFRP) Rebar's?

I am looking for any completed/ ongoing project in India where either Basalt FRP rebar or Basalt Fibres have been used

05 June 2018 9,174 0 View

Getting sudden change in stresses in Strands?

Hi I am trying to model FRP strands inside Prestressed Concrete. i wrote a UMAT code for defining Constitutive law for FRP. The linear analysis runs fine, however, after defining CDP I am...

09 October 2017 1,714 3 View

Can Hashin Damage Model for FRP laminates be Utilized in FRP Rebars ?

Hi, I am trying to model FRP strands (3D Continuum ) in ABAQUS. Since ABAQUS does not allow Hashin damage model to be utilized in 3D elements, I am planning to write a UMAT code for it. My doubt...

09 October 2017 2,013 0 View

What is wrong in the Code?

Hello, I recently wrote a UMAT code for FRP bars transversely Isotropic). But, while starting the job I get "Compilation Error". Can someone take a look at the code and suggest what is wrong in...

09 October 2017 5,570 0 View

Problem in Running Subroutine in ABAQUS?

I am trying to link ABAQUS 6.13 with intel parallel studio 2013 and visual studio 2010. On opening abaqus i get following notifications. (please see attached image ) Whereas while running the...

09 October 2017 6,653 2 View

Can I use Analytical Rigid Part to simulate Concrete Formwork in ABAQUS?

08 September 2017 9,315 0 View

How can i calculate the interface stresses in ABAQUS

07 August 2017 8,657 2 View

Can a prestress be Defined in a truss element in ABAQUS

Hello, i modelled a Pretensioned beam with tendons as solid elements. the model ran fine. Now i am planning to model the pretension beam with wire element instead of solid element, in place of...

31 December 2016 2,342 10 View

How to Define Loading Protocol in ABAQUS for Cyclic loading?

I have attached the experimental protocol for the test. My questions is 1) should I give this as it is in the tabular column while defining amplitude 2) what should i give the time period value in...

02 March 2015 1,725 4 View

Can anyone please help me to find the area under the hysteresis curve.

I am intending to calculate the energy dissipation during the 1st cycle of loading. i have attached the excel sheet which gives details for the 1st cyle of loading. i will be grateful if anyone...

01 February 2015 1,325 6 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View