How to add KCl to "INTERFACE 1010E" potentiostat/Galvanostat/ZRA's KCl electrode ?

More Kheira Nawel Benaissa's questions See All

Gauge Pressure and Operating pressure on combustion system?

Hi all, Please I have a question about the pressure: I am working on combustion, and I want to study the effect of pressure in my geometry, I couldn't understand where sould I put the pressure for...

14 February 2020 7,977 3 View

What will happen if I add the NO models (NO thermal and NO prompt) for the flamelet model using GRI mech? How Fluent works in this case?

Hi everyone, The GRI mechanism contain all the reactions, and species of NOx, and in the Fluent we can also find the NO models ( prompt, thermal and N2O..), when I added the models I found a big...

22 December 2019 3,785 5 View

I have tilt in my geometry, so Is there any way for doing Line moving with the flow ?

Dear professors and research scholars, I have a query for the code Fluent My geometry is not symmetric, I have tilt in my geometry so Is there any way for doing Line moving with the flow !!!...

19 February 2018 8,538 4 View

I have a problem with my results from FLUENT when I imported in ORIGIN, I have other lines! Does that mean the problem with the mesh or secondary air?

Dear professors and research scholars, Attached is a figure showing the distribution of the temperature along the central axis of combustor Fuel, I have problems with my results, When I put it in...

09 February 2018 738 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

Bapi Bera

Dear Kheira Nawel Benaissa ,

Can you please explain more about your question?

Are you want add more KCl solution in reference electrode?

Best Regards,

Bapi

Dear Kheira Nawel Benaissa

If you want to replace KCl solution follow the below link:

https://www.gamry.com/support/technical-support/frequently-asked-questions/reference-electrode-care-overview/

https://www.youtube.com/watch?v=d9n3-muB0cw

If you don't have extra glass frit and Teflon tube then just use same opening for removing and adding the KCl solution.

Cornel Radu

Never add KCl salt. Replace completely the solution or add only distilled water. Use a syringe.