i want to know , how should we add sulfur to molten steel in iron-making, in which method?
as tablet? granola? powder?
we manufacture alloy steel.
thanks
Sulphur additions are normally done in the form of cored wire. S containing core wire is added in the ladle furnace . It can also be added to the tapping stream
@ Mohammad Moodi Hope following link will be useful for you.
http://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.874.8713&rep=rep1&type=pdf
As I know the added of Sulfur to steel act as impurities and give low mechanical properties.
In general, it is added to improve machinability in form of cored wire.
It may be added as powder but inhomogeneity may cause severe deterioration of mechanical properties of steel.
Copper was used to enhance the machinability of steel more than sulfur.
thanks , but i want to know the best method for adding Sulfur as mentioned before.
before we use it as tablet but may be it's better to add as wire in ladle
Yes, the general practice is to add as wire.
Check with elingham diagram
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
Here's a serious question: If we were to stop emitting all greenhouse gases right now, would the Earth's temperature start to cool down, or would the existing greenhouse gases continue to warm the...
30 July 2024 5,123 4 View
Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...
24 July 2024 367 4 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
What protocol can be used to measure the cellular uptake of a nanoparticle? Is there a way to get more of a non-targeted nanoparticle into the cell? Why a fluorescent nanoparticle does not enter...
18 July 2024 7,153 2 View
Dear Gromacs users, I would like to simulate a zeolite-water system. In different literature, it is suggested to consider a rigid framework of zeolite to decrease the computational cost. I would...
15 July 2024 4,590 1 View
Hello, I have a problem in classification of "Additive Manufacturing" techniques. There are several classification for Additive Manufacturing e.g. Powder, Extrusion, Resin etc. Actually, I am OK...
15 July 2024 139 3 View
A question about scientific methodology
13 July 2024 2,160 8 View
We have conducted a systematic review to investigate the effectiveness of a treatment for a psychological disorder. We aim to report effect sizes and p values of the reviewed studies but one study...
10 July 2024 7,186 4 View
I participated in 2 research projects in which I was responsible for part of data analysis and figures production. Also, I spent hours trying a new statistical approach -for me- to implement in...
10 July 2024 1,226 5 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...
06 August 2024 5,023 1 View
How select composition for ods-high entropy alloys?
31 July 2024 2,795 1 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
Any suggestions with respect to etchant composition and holding time?
27 July 2024 6,925 2 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View