How should I specify the boundary condition between finite soil element and infinite soil element in ABAQUS?

02 March 2022 0 6K Report

And about the boundary condition of finite soil element that is not connected to any surface? Thank you!

Badges
Science topic

More Cheah Hang Moey's questions See All

For SIADH, does it cause edema and Hypertension?

I have found two teachings from different sources. One they said about blood volume increase and therefore the patient has oedema and hypertension. But, another source says when there is high...

08 December 2020 1,278 3 View

Can you recommend a task-based material that can be used to compare with the currently used textbooks in English teaching?

Hello everyone, It was my first experience for a research. I plan to explore the differences in grammar teaching in the two kinds of books: one is task-based and one is currently used in a...

29 October 2020 5,495 4 View

Application of Cronbach's alpha in Factor analysis (EFA)?

I read a lot of papers on the topic of "Factors Impact on Employee Satisfaction", which first proposed some possible factors, test the unidimensionality of a set of items belong to each specific...

13 September 2020 4,994 2 View

Colour of Methylammonium Iodide (MAI) in Isopropanol (IPA, 99.7%) turned slightly green after storing some time?

Has anyone observed the changes of colour of MAI in IPA to slightly green-ish after storing some time? I might have to prepare fresh solution again if this is abnormal. Could anyone verified the...

18 April 2020 7,504 1 View

How to connect Newport's Keithley SMU to perovskite solar cell to measure efficiency?

I have 4 crocodile clip wires, if I'm not mistaken 2 wires (red) connect to anode and the other 2 black wires connect to cathode. Both pairs of wires are plugged at the back of the SMU. Problem...

16 January 2020 3,000 2 View

Can I use Phillips Halogen Lamp (70W) to access the light stability of perovskite solar cell under ambient air condition?

We only have 1 Newport Xenon Lamp for PCE measurement. Is halogen lamp a suitable substitute for the Newport Lamp? We don't have the money to purchase another one solely for stability testing. If...

07 November 2019 5,294 6 View

What is the optimal diameter of the beads for extracting fungal DNA?

I want to extract fungi and bacteria DNA from skin swab. Some articles used two 5mm steel beads per sample, some used 0.4-0.6mm ceramic beads per 0.5g sample. And other diameter for beads were...

05 August 2019 6,471 1 View

What's the reaction temperature of Al-C?

Carbon fiber reinforced Aluminum martix composites prepared by liquid metal impregnation,when Al-CF begin reaction? The best way is attached some literature published in the journal of high...

03 August 2019 2,765 2 View

Weighting Methylammonium Iodide in ambient air with 40-60% humidity for perovskite precursor preparation?

Hi, i would like to know will the humidity (40-60%) of the room be detrimental to the MAI powder when weighting on the analytical balance? is the moisture sensitivity reduced when MAI is quickly...

25 June 2019 5,689 4 View

Determining the amount of HAuCl4.3H2O sticking on glass vial inner surface?

Since HAuCl4.3H2O (gold precusor) is very expensive, it is best to utilized it as much as possible. I have a glass vial that contains such gold precursor. Some of it are spread onto the inner...

28 May 2019 9,890 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Anyone with some Transgenomic Wavemaker software? Seeking help from the chromatography community?

I am trying to seek out some Transgenomic Wavemaker software (happy to purchase a computer too) to operate a fraction collector. The only way to connect to the fraction collector so far is to...

23 February 2021 9,181 1 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

How to validate regridding results of environemental data to higher spatial resolution in R?

I am working with several continous, environmental marine datasets at varying original spatial resolutions. My aim is to regrid each dataset to one common, high resolution grid. I am currently...

22 February 2021 2,290 2 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View