How should i select RPM and Axial load in joining of particular aluminium alloy to copper alloy?

More Gurunath Shinde's questions See All

I am looking for underwater friction stir welding experimental set up to conduct Al-Cu plate welding of 3mm thick?

Underwater friction stir welding set up in india for Al-Cu plate welding

02 March 2018 5,577 4 View

Please suggest some research topics in micro fabrication of BioMEMS?

Microactuators,Microsensor,Microgrippers,Cantilevers,Microfludic devices

08 September 2015 3,460 1 View

What is the application of shape memory alloy in BioMEMS?

BioActuators,BioSensor,Micromachining etc

07 August 2015 4,681 2 View

I am looking for research topic on aplications of smart materials in biomedical engineering.Should anyone suggest topics in these areas?

Smart materials in Biomedical Applications their tribological behaviour and enhancement

06 July 2015 2,606 1 View

Should we use simple vertical milling machine for friction stir welding of aluminium copper alloy?

milling machine specification required for Al Cu FSW.

01 January 1970 1,766 4 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to calculate the proportions in grams or milliliters of the compounds for 60 mL of SAPO-11 zeolite precursor gel?

It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...

01 July 2024 617 3 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Dragan Vuksanović

Dear Sir,

I hope that this link and studies would help you to find the answer at your question. Good luck with your project.

Best regards,

http://www.istp.org.in/files/DAP-Ph.D%20Thesis-ISTP.pdf

Masoud Yousefi

I have the same experience. the best experimental result is in 800RPM for different aluminum-copper alloys.

for further details you can see attached article.

Isaac Dinaharan

Please refer the attached file.

Kush P Mehta

you may refer

http://www.tandfonline.com/doi/full/10.1080/10426914.2015.1025971?scroll=top&needAccess=true