How Should I Fixed following errors in Abaqus?

More Maaz Ahmad's questions See All

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Gromacs first step of minimization ?

I have face this problem anyone help me how to solve this issue ?which is below Fatal error: There are inconsistent shifts over periodic boundaries in a molecule type consisting of 78 atoms. The...

07 August 2024 2,598 1 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

How to we see transcription activity of the bhlh79 family is at the N-terminal or C-terminal?

I'm a PhD Student. From Northwest Agriculture and Forestry University China. My Problem is this I start my work on bhlh79 transcription factor gene. I do my Y2H 5 time but the colonies appear on...

30 July 2024 1,412 8 View

How apply Kao Residual Cointegration Test in eviews?

Kao's panel cointegration tests , is there anyone willing to explain me the eviews-9 output for the Kao's panel cointegration tests?

23 July 2024 5,051 4 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

When I am trying to distill triethyl amine while drying it over calcium hydride. How do I design the setup to let hydrogen escape without losing NEt3?

I am new to research. The boiling point of triethyl amine (NEt3) is 89 degrees centigrade. I am skeptical that when I will let the hydrogen escape which is getting generated in situ, I will also...

21 July 2024 7,284 4 View

Why my gel electrophoresis have shadow bands? Please see the attached picture for the gel electrophoresis ?

Sometimes I see the shadow like bands and its not true band. I want to know that what's the reason for it. I am using 2% gel for running genotyping samples I have uploaded the gel picture in both...

19 July 2024 148 6 View

What is the future scope of acoustic emission?

17 July 2024 1,510 1 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Does continues partial charging/discharging do any harm to the BESS performance and degradation?

For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...

01 August 2024 9,903 7 View

How to Post-fix Mice pup's brains?

I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...

31 July 2024 1,123 4 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Hasanain Radhi Radeef

Check this link...

https://www.eng-tips.com/viewthread.cfm?qid=191374

Maaz Ahmad

The model Analysis run for a load of 1 Mpa or less but when I increase the load it gives me such errors?

Model Pic is attached which interaction can i used for support and loading plates?

General contact, then can chose between self selected surface or the surfaces being selected by you. Also you need to set friction when defining the interaction.