How I can prepare conductive thin film from polyaniline (emeraldine salt)?

More Islam Al-Shurman's questions See All

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

In w/o/w double emulsion solvent evaporation method When w/o emulsified witlh outer phase, WHY the sample agglomerated immediately....?

The w/o phase sonicated for 60 second by prob sonicator... And double phase water Sonicated for 3 min..

07 September 2020 5,419 1 View

What is the problem in this bacterial growth?

Are there any bacterial growth in this agar plate? Or what is the problem for that??

26 August 2020 994 10 View

How I can have a continuous thin film by spin coater?

Every time I have not a continuous thin film , my sample deposit in a dispersed areas after spin coating, what can i do or what is the problem for me?

11 December 2018 4,184 11 View

How to make a better plant water extraction ?

I'm working in plant extraction by using the soxhelt with different solvents , so can i use water as a solvent in the soxhelt apparatus ... if i cant , What is the best method of water extract???

06 July 2018 5,487 3 View

How can I have a conductive thin film by spin coating ?

The solution is conductive but when i convert it to solid (thin film) by spin coating the film is not continuous and not conductive, there is not any spot in the film on glass substrate...

01 January 1970 6,788 3 View

What is the most conductive polyaniline emeraldine salt or PEDOT?

Which one is more conductive thin film polyaniline emeraldine salt or PEDOT? Also which one is easy to prepare thin film from it? If there is any procedure can help this can make a sense. Best wishes

01 January 1970 2,794 2 View

Can I have a conductive and transparent thin film from polyaniline (emeraldine salt)?

I have to prepare thin film from polyaniline (emeraldine salt) powder, I need a suitable and easy method by chemical reaction, also I have to use the spin coating?

01 January 1970 983 10 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

How can we obtain a modification factor for creep parameters?

I want to obtain standard creep parameters of salt rock by creep parameters of rectangular samples. Is there a modification factor to convert creep parameters of rectangular (prismatic) rock salt...

01 March 2021 7,131 1 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Islam Al-Shurman

@Vipin Kumar

Azhar Ali Haidry

Islam Al-Shurman ,

you should read this paper carefully, this is comprehensive review paper polyaniline coatings.

Article Progress in preparation, processing and applications of polyaniline

Upendra Mahatme

Dear Islam Al-Shurman,

Try to use aceton to disperse PANI-ES. Use high quality filter paper. Before this check that whether PANI is in ES form or not.