How i can input temperature depedent stress strain curve for concrete & steel in ansys?

More Tanu Garg's questions See All

DMSO concentration in cell culture? Precipitating while PBS is added?

I am testing a compound on RAW 264.7. the compound is soluble in DMSO. but to ensure that final concentration of dmso is not more than 0.1%, we are first dissolving it in dmso and then diluting it...

11 February 2021 1,136 3 View

ANSYS APDL RC Beam modelling?

Hello I have modelled RC beam in ANSYS apdl. first create volume, then create keypoints & create a line joining that keypoints to make reinforcement. I am working on thermal analysis, for...

20 January 2021 7,344 2 View

ANSYS APDL tabular entry related?

Hello I want to add thermal convection load on specific area of concrete volume. it asks for film coefficient which is a constant value but the bulk temperature has no. of values that i have as...

18 January 2021 6,627 1 View

What is the best way to maintain constant concentration of a volatile organic liquid in an open experimental set-up?

The purpose is to keep a NAPL (eg Toluene) concentration constant in an open tank set-up.

27 December 2020 7,325 2 View

What are some best features that can be added in IoT based pollution monitoring system ?

Actually I am developing IoT based pollution monitoring system and need some ideas which help in developing great product with great features

10 October 2020 5,657 7 View

Can LoRa Technology be used for managing underwater data center ?

As per the latest research, Microsoft finds underwater data centers are reliable, practical and use energy sustainably so how can we enable IoT with LoRa technology in the underwater data center...

05 October 2020 535 4 View

How can I calculate the concentration of nanoparticles being used in UV-visible absorbance scan?

I have taken 1000 PPM of nanoparticles in 1 ml of RO water and pursuing its UV visible spectro absorbance scan. They are showing respective peaks on the baseis of energy transition of electrons...

19 September 2020 6,276 3 View

How can Gold be extracted from mining concentrates?

I work at a precious metal refinery. We extract gold using aqua regia. However, sometimes Gold does not dissolve in AR. Sometimes it precipitates due to cold weather? Is there a way to make sure...

07 August 2020 7,059 3 View

Chemistry behind synthesis of boron nanoparticle?

Hello everyone, I want to know whole chemistry behind synthesis of boron nanoparticle via chemical and biogenic methods. Focussing on why naked boron is not used as I have seen in papers, boron...

05 August 2020 1,195 14 View

How can we characterize a polymer-textile substrate interface interaction?

When a textile surface such as cotton fabric is coated with a polymer with thickness approx. 20 micrometers, what will be the sample preparation, parameters, and technique to determine the...

26 July 2020 7,343 8 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Kumar Ujjwal

Go to Preprocessor> material models>structural>nonlinear>elastic>multilinear elastic

enter stress and strain values with temperature

Arun Patil

Dear madam,

You can easily work temperature dependent stress strain curve setting in ansys workbench in engineering parameters setting ... post processing is comparatively better