Can anyone provide me with the name of some new books which they discuss the industrial robot applications?

Can anyone provide me with the name of some new books which they discuss the industrial robot applications especially for the pick and place applications and how we can choose a suitable robot for...

03 April 2016 7,024 0 View

Which algorithm is used for path planning in case of scara robot? Is it in task space or in the joint space?

Which algorithm is used for path planning in case of scara robot? Is it in task space or in the joint space?

11 December 2015 309 7 View

Is the path planning for industrial Scara robot in task space or in joint space for?

11 December 2015 6,331 2 View

How I can minimize the cycle time for an industrial robot?

31 December 2014 5,356 7 View

What are the value of costate in (tf) when the the problem is Lagrange problem?

10 November 2014 2,372 3 View

Can I discratizie the differential dynamical equations for the robot or not?

if some one has references, examples or book please send to me?

09 October 2014 6,225 2 View

How I can find the best step size for the steepest decent method?

I'm using the steepest decent method to find a solution for optimization problem. Can someone please guide me to the best method to find the step size to speed up the convergence rate?

08 September 2014 8,391 6 View

Can the steepest descent method be success if the initial assumption for the solution is poor?

07 August 2014 2,528 9 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

Is it okay to mention you distributed your qualitrics study link through social media sites?

Just want to be clear and know it is okay to say I have distributed the qualitrics link through social media such as Facebook, Instagram and Twitter to ensure my target audience is reached in my...

21 February 2021 5,143 2 View