How i can coat a steel cord (wire) by brass coating soluting?

Safie Anjomshoa @Safie-Anjomshoa

21 August 2024 0 10K Report

i work on operation of steel cord coating by brass for a golden color, i wanna know the materials to make the solution.

Badges
Science topic

More Safie Anjomshoa's questions See All

Help with insect identification?

Could someone help me identify the insect in this picture?

31 December 2020 5,858 10 View

How to analyse 2 cross correlation graph?

i have 3 cross correlation data between cross section 1-2 , 2-3 and 1-3..graph 2 make more noise than graph 1 and 3..and i know that the maximum lag of the graphs show that the most similarities...

11 December 2018 2,706 1 View

How to increase MLSS in aeration tank from 5000 mg/l to 12000 mg/l ?

I have an aeration tank and feed it with wastewater. MLSS tests show that the growth is slowly, only 400 or 500 mg/l per day. my tank MLSS is 5000 mg/l and my target is 12000 mg/l.

07 July 2016 9,332 14 View

How can i make solutions with specific CODs?

i have a sample that i want to find its COD. i had fined a COD testing method ( that uses permanganate for measuring COD) but i dont know Accuracy of this method. now i want make some standard...

19 June 2016 6,809 6 View

How to have access to healthcare in Sweden?

Funding

17 March 2014 2,149 1 View

Is skin yellowness an numerical or ordinal variable?

I have a response variable called skin yellowness, which I will measure via a scored color chart, whereby 1 is pale yellow and 15 is orange. I'm not sure if this counts as an ordinal variable,...

11 August 2024 4,793 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What Are the Best Alternatives to the MTT Assay for Assessing Cell Toxicity of Colored Herbal Extracts?

I am currently investigating the cytotoxicity of a series of herbal extracts, and like many studies, I have been using the MTT assay to evaluate cell viability. However, I am encountering a...

31 July 2024 193 4 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Why applying a saved template of a bar chart in a different/new one doesn't take effect in SPSS?

Using SPSS, I made my edits in one bar chart — e.g., font type and size, hiding grid lines, and colours, namely: blue, orange, green, purple, and grey for 5 bars, respectively, etc. — and I saved...

29 July 2024 1,981 1 View