Does all mineral oil contains asphaltenes?

I had a mineral oil of 460cSt (containing sulphur and phosphorus), after addition of nanparticles (carbon nano tubes and graphene) the viscosity decreased significantly. literatures says that the...

07 August 2018 9,447 1 View

What can be the reason for high coefficient of friction and low wear scar in a lubricant containing carbon friction modifier and zinc oxide?

A lubricant contains zinc oxide nano particles and carbon FMs, the coefficiet of friction is high while the wear scar diameter is less for the samples. The load was 392N @1200rpm @75degree C.

03 April 2018 3,084 6 View

Does the coefficient of friction values depend on the type of tribometers used?

Experiments were carried out using pin on disc apparatus (120N, 800rpm, a flat faced pin 10mm, room temperature) and four ball test(120N,800rpm , AISI 52100 balls , 75 degree C). The lubricant...

11 December 2017 3,529 2 View

What is the Youngs Modulus of Zinc Oxide Nanoparticles?

Elastic modulus of Zinc Oxide nano particles

07 August 2017 7,994 2 View

How to explain the phenomenon of extreme pressure properties in case of graphene and carbon nano tube?

Graphene and carbon nano tubes shows better extreme pressure characteristics when used as additives.

06 July 2016 8,544 0 View

Can anyone tell me some applications where we use gears of hardness 22Rc-30Rc?

Specific Application please.

06 July 2016 3,358 2 View

Which is more preferable mixed lubrication regime or boundary lubrication regime?

06 July 2016 9,847 7 View

How does Young's modulus,shear modulus,Poisson ratio of a nano wire/tube/particle influence the coefficient of friction?

Mechanical properties influencing coefficnet of friction.

05 June 2016 1,316 2 View

Which roughness parameter would be more suitable to compare between steel surfaces : average roughness,skewness or kurtosis?Why?

05 June 2016 3,356 3 View

Does graphene exhibits better frictional properties than carbon nano tubes?

Graphene shows better frictional properties than carbon nano tubes.

05 June 2016 2,558 1 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

How can I calculate teh crystallinity degree of graphene oxide?

I had treat my XRD diffraction pattern by Highscore to calculate the crystallinity degree Xc and I have the formula but I dont no the 2Theta of Ac and Aa to calculate Xc. Is it like polymers...

10 February 2021 6,305 5 View