Hi,
Can somebody prove it?
Regards,
Suhas D
Does anyone know how to perform a sensitivity analysis for crop evapotranspiration ( FAO Penman-Monteith equation) using daily meteorological data?
27 December 2020 9,552 3 View
I have modeled the lumped element circuit for the 3D structure which has been simulated in HFSS. Now I need to derive the equations for the lumped elements keeping the S-parameters of the...
23 December 2020 172 3 View
For academic writing.
17 December 2020 6,465 5 View
Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...
13 December 2020 4,329 5 View
What I understand is while applying continuous control to a continuous-time system in MATLAB simulations, actually the control is being applied in discrete manner inherently due to the nature of...
28 November 2020 1,866 4 View
I tried to simulate a maglev system with continuous time sliding mode but my simulation is showing error (there is a singularity at one of the integrators). I am attaching the modelling and...
16 November 2020 8,964 7 View
Suppose 2 methods are shown to do sliding mode control of a given system. Please tell me if we can compare chattering in both by MATLAB or some other way
16 November 2020 3,251 3 View
I am working on Mg-based metal matrix composites. I added two different types(A&B) with a suitable percentage(1%,2%,3% and 0.5%,1%,1.5%) of ceramics separately using DOE and tested. Now I want...
14 October 2020 2,984 9 View
Ti based C94 catalyst is required for PBAT synthesis
12 September 2020 7,174 4 View
My concern is to use Headonic regression model for market price index analysis.
10 September 2020 9,466 3 View
can anyone help me in this, it will help me with my research work
01 March 2021 834 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
I have done electrochemical impedance by using cyclic voltammetry for one organic material. from that, I plotted bode diagram. but actually, I am very confused about how to find the capacitive...
18 February 2021 3,023 3 View
I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...
16 February 2021 8,514 2 View
I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...
09 February 2021 375 2 View
Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...
09 February 2021 6,799 8 View
I am looking for gas permeability of PDMS for simulation in COMSOL MultiPhysics and using creeping flow , fluid and matrix properties. The permeability unit in COMSOL is m^2 whereas I have the...
08 February 2021 4,305 2 View
I have a design with 2 dipoles working at different frequencies joined in one system and separated by Ferrite. I think, Ferrite was used to minimize the interference between 2 antennas as much as...
25 January 2021 5,918 3 View
I'm looking to compare a few fluorescent dyes for cell permeability. I'm interested to see how much of the dye actually enters the cell, but would specifically like to quantify this data. Any...
21 January 2021 6,089 3 View
Hi all, What I know the permeability of matrix and fracture can be in a broad range in fractured reservoirs. Am looking for the most usual range for their permeability separately. I will be highly...
15 January 2021 5,271 2 View
