Hi,
I simulate the flow around a Savonius turbine using the technique of Sliding Mesh. I have the file containing the values of Cm, but I don't know how to use it with Area weighted average to pull off the correct value.
I have prepared half cell. Lithium is considered as anode in the system. Whereas, I would like to know what is actually capacity retention? How it can be calculated mathematically? On what factors...
02 June 2024 4,135 0 View
I have been working on electrospun membrane for Lithium Ion coin cells. I have tried to control different parameters, such as, thickness, electrolyte amount and many other parameters. I am facing...
26 March 2024 2,786 0 View
Everything is standardized as per protocol, but still this smearing is there, need suggestions from PCR experts. DNA extraction by the magnetic beads-based method. tried colony Pcr. PCR...
01 January 2024 6,888 4 View
As i asked in the question statement, I observed a little amount of PP is soluble in cyclohexane. If i want to prepare a 4 %w/w solution of PP in cyclohexane, it is obvious all of it will not be...
03 November 2023 5,905 4 View
I dissolved a medium molecular weight polymer at 135 degree celcius and after removing it from flask, i poured it into glass bottle for further use but it became a gel like structure. Can anyone...
03 September 2023 8,436 3 View
SCAPS-1D software for perovskite solar cell simulation.
01 September 2023 4,219 0 View
for perovskite absorbers like (bandgap (eV),electron affinity (eV),dielectric permittivity (relative),CB effective density of states (1/cm^3),electron thermal velocity (cm/s),electron mobility...
27 August 2023 2,194 2 View
27 August 2023 3,500 2 View
Is high molecular weight PLA a good choice for application in elastomers? The molecular weight (Mw) of PLA I am planning to use is 80000. Kindly suggest if other biopolymers are suitable instead...
28 May 2023 5,401 1 View
I have to use poly lactic acid for one of my experiments. The weight average molecular weight of poly lactic acid is 80,000. How i can convert Mw to Mn in order to calculate given amount of mass...
23 April 2023 2,418 2 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....
24 July 2024 4,058 5 View
In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?
13 July 2024 6,296 5 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
I am a student of Mechanical Engineering. I am doing CFD opf Archimedes Winf Turbine. I am trying to validate the result of Paper. But the problem is that tha value of Power Coefficient is ever...
05 July 2024 6,839 2 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Hi! I'm simulating a specific material on Quantum Espresso, and I found something strange. Initially I've performed simulations on FCC InAs crystal and I used the Hubbard correction to reproduce...
02 July 2024 9,323 1 View