Hello, I have a 3D model and I wanna run a 6DOF dynamic mesh simulation, I need the settings, I run it but the turbine does not rotate. I do not know the reason. Any help?
Thanks
Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...
08 September 2019 688 2 View
Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...
05 June 2019 8,078 4 View
Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!
05 June 2019 7,188 12 View
Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...
04 May 2019 6,100 3 View
Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks
04 May 2019 4,064 2 View
Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!
03 April 2019 2,799 6 View
Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks
02 March 2019 6,112 4 View
Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks
31 December 2018 5,908 5 View
Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!
31 December 2018 934 3 View
Hello, I have this UDF and it says that the airfoil changes the degree to +/- 8 through 1 sec, how is to work and how can we control the angle? /**********************************************/ /*...
09 October 2018 4,673 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,629 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...
06 August 2024 4,953 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View