How do we can show special parameter in visualization in the abaqus result like rupture index?

19 February 2018 1 7K Report

I want to determine rupture index in ABAQUS but there is not exist this parameter in output result so i have to write special code for this. i do not know how i can write this code. i want to show rupture index like Mises stress in result.

thanks.

Behnam Karami

Hi dear Dr. yeqing ,thanks a lot .

Your message was very helpful to me. i am a beginner to write Abaqus subroutine USDFLD .may you introduce a good source for writing the code?

Badges
Science topic

More Behnam Karami's questions See All

Why did the authors design a sociodemographic questionnaire?

This is a question from a journal reviewer who asked my manuscript. Can someone please guide me on how to prepare the reviewer's answer? Thanks. here is reviewer question. why did the authors...

16 November 2020 735 2 View

How can I fix the capacity curve of two different structure?

I have two frames for nonlinear analysis, one of them is CBFs and one of them is BRBFs ( the generals are the same, only lateral elements are different). When I drew the capacity curve of my...

11 November 2020 10,034 3 View

Hi Has anyone treated the wastewater of alcohol production units (specially ethanol units) with advanced oxidation methods?

if anybody uses these methods on an industrial-scale, please let me know. I wanna ask a few questions and I want information. thank you.

25 October 2020 8,605 2 View

Convective drying of a wet object in Ansys Fluent?

I have a wet object to dry by convection. The "object" can be treated as a porous medium or semi-solid. Do you have any idea about solving it in Fluent. This is a conjugate heat and mass transfer...

31 August 2020 6,646 5 View

What is the best method to predict the water consumption of EACH customer for the next month?

Say we have a dataset that has the following attributes: - customer_id: There are a total of 1000 customers, each of them with a unique customer_id - observation_date: The date on which we...

01 August 2020 5,376 5 View

Why Mean Absolute Percentage error is too high?

I would like to make a comparison on the performance of some regression algorithms according to different performance criteria, including Root Mean squared Error (RMSE), coefficient of...

10 July 2020 5,463 7 View

Why the initial pressure in a fluid cavity simulation in Abaqus fall to zero just at the starting increments?

I am using fluid cavity capability for simulation of a water-filled container with Abaqus-Static-Standard. The container has an initial pressure and is been surrounded by another solid layer with...

21 March 2020 7,153 3 View

How can I save normal directions of solid elements in Abaqus?

Dear all, I need to have normal directions of solid elements in my 3D simulation with Abaqus. I know that in Visualization Module, Options tab> common or superimposed, there is the possibility...

28 February 2020 2,703 3 View

How to accelerate running the first(geostatic) step in Abaqus?

Hi all I have modeled an excavation in three steps in Abaqus software. The model has 4 steps. The first one is the geostatic step and the rest of them are excavation steps. I am using Umat...

24 January 2020 6,821 2 View

No title

I'm trying to collect milk from our knockout mice (at the end of the lactation stage) to isolate milk exosomes. But I have a hard time with milk collection from mice. I have used either pump or...

22 January 2020 4,527 1 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

How can I publish a manuscript in free or low cost journal with good H-Index?

Dear all I am going to publish my manuscript which is from my thesis in a good H-Index journal but I found them very expensive(I don't have financial support) based on the exchange currency of my...

28 February 2021 7,800 6 View