How do the installation for nitrogen cooling molds in a vacuum?

12 December 2015 0 2K Report

I want to apply the apparatus to produce amorphous alloys by sucking in cooling the mold pairs of nitrogen rather than water. The chamber is an inert gas argon.

Badges
Science topic

More Marcin Nabiałek's questions See All

How to explain the high coercivity field for amorphous materials?

I mean materials with a value of coercivity in the range of 500-5000 A/ m.

03 April 2016 2,903 0 View

What is the relationship of the effective anisotropy and coercivity field in soft magnetic materials?

Exactly I mean bulk amorphous alloys.

11 December 2015 6,871 1 View

How can I translate the Herzer diagram for nanocrystalline materials?

I mean the diagram describing the change in coercivity with the volume of nanocrystalline grain. Of course, for soft magnetic materials. I understand this relationship but I mean the explanation...

11 December 2015 2,552 4 View

Any advice on anealling by impulse current bulk amorphous alloys?

I need information about annealing the impulse for bulk amorphous materials

11 December 2015 7,578 1 View

How would you describe the impact of the transition phase between grain and amorphous matrix?

I'm interested in how to interpret the transition between the grain and the amorphous matrix.I am interested in metallic materials. Andrew thank you for your attention. The transition phase...

11 December 2015 679 11 View

Who deals with the description of the structure of amorphous ferromagnetic alloys?

I'm interested in whether someone deals with changes in the structure of amorphous without nanocrystallization. A description of those changes based on the theory of H. Kronmüller (approach to...

11 December 2015 7,379 5 View

How can I describe the distributions of low-component induction hyperfine field at the 57Fe for soft magnetic alloys?

The component is well separated with a small probability. Of course, in terms of schedule for amorphous alloys. The spectra performed in transmission geometry.

11 December 2015 7,042 1 View

Who has tried to do bulk ferromagnetic amorphous alloys with two amorphous phases?

I mean if someone did ferromagnetic amorphous with two separate magnetic phases at different temperatures Curie. In addition, if these materials have a high Ms small Hc.

10 November 2015 6,968 8 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Can we isolate microplastic from sludge sample without using vacuum filter..?

isolation of microplastic from sludge sample using centrifugation ..

23 July 2024 6,418 0 View

What is the mechanism of atmospheric pressure plasma Jet (APPJ)?

In general, the characteristic of electric current as a function of voltage in argon plasma jet using dielectric barrier discharge in atmospheric pressure, jet length will increase by the increase...

16 July 2024 9,316 1 View

Help me to identify these fungal slides?

These fungal slides are isolated from cultured Bread mold on PDA media and smear is treated with Lacto phenol Blue dye ..

13 July 2024 9,701 1 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View