How do I use system dynamics modeling approach for demand planning and forecasting in consumer packaged goods industry?

More Veerendra K Rai's questions See All

What condition of Kirat Rai's participation in politics before and now in Nepal?

The political participation of the Kirat Rai community in Nepal has evolved significantly over time: Historical Context Historically, the Kirat Rai people, like many indigenous groups in Nepal,...

05 August 2024 5,950 1 View

Is there any paper published which evaluates the effectiveness of "GaitOn running gait analysis software" ?

I am doing a comparative study in which I will check the patient's progress by assessing their gait parameter, and to do that I will be using the abovementioned software. Still, before that, I...

17 July 2024 6,552 2 View

Method for estimation of biomass using non-destructive method for ornamental plants?

Allometric equations are available for trees but couldn't find any method/equation for ornamental plants?

04 July 2024 2,646 1 View

How to find value for Ki (inhibition constant); Kd (dissociation constant), and Km "equilibrium constant?

Hello, I got reviver comment " please look into the comparative assessments regarding Ki (inhibition constant); Kd (dissociation constant), and Km "equilibrium constant" of the target...

09 June 2024 10,069 3 View

Any idea or sample data used for simulating gasket (using gasket element type) material with a pressure-closure curve and other details in Abaqus?

It is a sponsored project to develop a gasket made up of FGM material and validate the nonlinear behavior of the FGM using Abaqus simulation. I was exploring the behavior of the gasket element...

25 May 2024 2,407 0 View

How is it possible for two or more 2D materials of same family to show same raman peaks?

Such as H phase MoS2 and VS2 show same raman peaks.

08 May 2024 4,379 3 View

Is there any open access software like sci finder to know about published paper?

Sci finder helps to find out the research that has published.

30 April 2024 6,287 0 View

What are the design constraints of winglet?

Design constraints such as strength requirements, and size limitations are to be considered while designing winglet

26 April 2024 6,857 2 View

Why the Erro comes in SCF when running SOC+U using Quantum Espresso 7.3?

Hi all, I encountered an error while running SCF with SOC+U using Quantum Espresso 7.3. Here is the error%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% Error...

09 March 2024 9,104 4 View

Can a particle be its own antiparticle?

Quantum Entanglement is a phenomeno inwich

03 February 2024 3,685 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

In what part of the brain´s rabbit bdnf is located and include references please?

I´ve been unable to find specific information about this neurotrophin in the CNS of rabbits exclusively. There is extensive info in mice, fish and rats, but in brain´s rabbit is hard to find....

04 August 2024 762 1 View

Suhas Gaikwad

propose set of equations for for demand planning and simulate that to get foresting for the CPG industry

Mohammad Mirkazemi

You can see this references:

Campuzano, F., & Mula, J. (2011). Supply chain simulation: A system dynamics approach for improving performance. Springer Science & Business Media.