Runs of nucleotides in Sanger sequencing?

I performed site directed mutagenesis, transformation, and then I sent out plasmids for Sanger sequencing and found out that there is extension of DNA just before the stop codon. I am not sure...

27 February 2021 547 3 View

RNA-seq DEGs downstream analysis and reporting in literature?

I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...

23 February 2021 8,969 1 View

What is the best method to evaluate and measure non-circulating estrogen levels in mice ?

Could anyone suggest me the best procedure to measure the circulating estrogen levels in mice ? I came across the general methods where it can be measured in serum or urine but a detail suggestion...

22 February 2021 4,352 2 View

Helicoverpa armigera eggs are not hatching in lab condition, why?

Dear RG friends, I am providing a complete H. armigera diet for larvae and maintaining the eggs in the growth chamber as well as in-room conditions. But since three months, eggs laid from the...

21 January 2021 5,546 32 View

Why am I getting 2 bands for Gibson Cloning Vector PCR?

Hi, I designed Gibson primers (2 primers for fragment and 2 primers for vector) using snapgene. Then I ran PCR separately for Fragment and Vector. Fragment DNA was found to be the correct sized...

11 January 2021 9,500 2 View

Was there any pesticide disasters other than Bhopal and Kasaragood tragedy around the globe?

Pesticides become prime compo in agricultural activities to meet the growing demand of the human population. But indiscriminate usage and mishandling led to two disasters in India such as Bhopal...

11 January 2021 3,790 7 View

Which is the most recent and updated classification of Class: Insecta?

Based on the many publications from several decades, we came across many classifications of Insects. Among them which one is more updated and approved classification that can be used for research,...

05 January 2021 3,668 9 View

Can we mix elemental powders of 325 mesh using an agate mortar and pestle?

Elemental Powders like Titanium, vanadium, tungsten, zirconium, hafnium.

04 January 2021 7,357 1 View

How can we say a species of insects got extinct?

02 January 2021 4,232 10 View

No title

It is important for me to know the opinion from your point of view as researchers.

30 December 2020 988 2 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View