How do I make direction dependent cohesion and friction angle using Drucker-prager constitutive model for anisotropic soil in Abaqus?

Digvijay kumar Singh @Digvijay_Singh6

11 November 2015 1 9K Report

How we can assign cohesion and friction angle using Drucker-prager model for anisotropic behavior of soil in abaqus ?

http://www.egr.msu.edu/software/abaqus/Documentation/docs/v6.7/books/usb/default.htm?startat=pt05ch18s02abm20.html

Babu Bhaskaran

Refer this link:https://en.wikipedia.org/wiki/Drucker–Prager_yield_criterion

Refer this link:www.egr.msu.edu/software/abaqus/.../docs/v6.7/.../pt03ch12s08s02.html

Refer this link:people.ds.cam.ac.uk/jae1001/cus/.../han_etal_jsolidsstruct_2008.pdf

Badges
Science topic

More Digvijay kumar Singh's questions See All

How to plot Volumetric strain vs axial strain for three dimensional drained triaxial test on Loose sand from ABAQUS .odb File?

As it is known that volumetric strain is (LE11+LE22+LE33). I followed the following steps: 1.) Extract LE11 for whole model and average it 2.) Extract LE22 for whole model and average it 3.)...

04 May 2015 941 2 View

How can I plot deviatoric stress vs. axial strain of whole model in triaxial test from odb field output in Abaqus?

Thanks in advance for your replies.

03 April 2015 5,079 8 View

No title

I am modeling drained triaxial compression test. I modeled soil as cylindrical part in abaqus. Bottom part of cylinder is fixed and on top displacement is applied. I used Dynamic/explicit steps....

03 April 2015 2,027 10 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View