I am trying to simulate phase change of refrigerant inside pipe extracting heat from panel in comsol. Can anyone help with how to simulate this?

My model is a rectangular multi layered structure under which refrigerant flows through cylindrical pipes. A heat flux of 600W/m2 applied on panel and internal forced convection is used for...

20 January 2021 9,478 1 View

Why does the ghost atoms gives error in NICS calculation with wb97xd in gaussian09 ?

In a trial, I am trying to calculate NICS (0 and 1) values for benzene ring using gaussian09. I have placed the ghost atoms at the center, 1A, and 2A above the rings. On using the method/basis...

19 January 2021 3,188 3 View

Rejected manuscript for journal publish after 1st revision, what needs to be done next?

Hello, My manuscript has been rejected by the editor and reviewers even after the 1st revision. Though I tend to disagree some of the points raised, assume I can't request for another revision...

28 December 2020 6,062 3 View

Acetylene reduction assay procedure?

Do anyone have the detailed step wise procedure(practical) to do the acetylene reduction assay? Or if anyone can let me know in which institute can i analyse my samples in India?

28 December 2020 6,717 2 View

How to capture UV- fluorescence from a substance using a camera?

I have a liquid that glows when UV light is shined. However, when I use my phone camera I can't see the glow, I just see a violet hue. What is the best way of capturing the fluorescence-glow from...

02 October 2020 8,664 3 View

What is the actual basis on which amount of Perovskites materials are to be taken?

In some discussion people took 112 mg of MAI and 461 mg of PbI2 in 1 mL DMF and some took 461mg of PbI2 too but 159mg of MAI there are many other authors took different amount of these materials...

17 September 2020 9,998 3 View

Forums to get online survey responses?

For my journal publish, I have been asked to increase the sample size by 200. I have been individually contacting more than 1000 Linkedin contacts and posted in all professional groups. But have...

04 September 2020 2,564 5 View

Derivation of Rice and Tracey equation???

12 July 2020 6,555 1 View

Can anyone suggest me where to get a low cost 2D Heterostructure Transfer System?

Except the 2D transfer system sold by HQ Graphene

09 July 2020 3,276 4 View

What digital technologies are more helpful to sustain Agriculture?

With the global Corona Pandemic situation, it looks to be inevitable to move towards digital technologies to get adapted in various farming sectors. With the advent of IoT, Robotics, Data Science,...

10 May 2020 8,570 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View