How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View