How could we defined the orchid-mycorrhizal interaction using molecular tools?

More Aheibam Loyanganba Meitei's questions See All

The amplitude of frequency in FFT doesn't match time-domain amplitude in COMSOL Multiphysics software?

Dear friends I am designing a underwater optical acoustic sensor Using COMSOL Multiphysics software. I would like to analyze the received signal signal by sensor in both the time domain and...

26 August 2019 1,925 3 View

How to calculate the sensitivity of the acoustic optical sensor?

Dear friends, I am modelling an optical based underwater acoustic sensor to detect the acoustic sound wave which is induced inside the water-filled tank using COMSOL Multiphysics software. Due to...

24 April 2019 2,198 3 View

How to convert the output voltage(Volts) of Piezoelectric sensor into pressure (Pascal)?

Dear friends, I am working on an application where I need to convert the o/p voltage(in volts) of Piezoelectric acoustic sensor into pressure (in pascals). I wanna know how I would be able to do...

27 December 2018 3,832 8 View

Can used Piezoelectric transducer as an acoustic wave signal receiver sensor?

Dear friends, I am going to design a piezoelectric transducer as an acoustic wave signal receiver sensor using COMSOL Multipysics. Description of the model: In an air-filled rectangle box an...

24 December 2018 6,104 7 View

Is springer nature book series Index by scopus?

01 January 1970 5,334 13 View

Is De Gruyter a good journal publisher?

01 January 1970 3,936 3 View

Edge Is Much Shorter Than The Specified Minimum Element Size?

Dear friend's, I am trying to mesh a 3D integrated concrete block model using COMSOL software. The geometry is somewhat complex. The error warnings in the progress frame are: Mesh error (ftet1):...

01 January 1970 2,251 3 View

How to apply continuity boundary condition at the interface between two medium in COMSOL Multiphysics?

01 January 1970 3,220 11 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View