How could the variation of soil permeability with the void ratio be defined so as to dissipate the excess pore water pressure?

09 September 2017 1 2K Report

Cheers!

Simply when void ratio increases permeability increases then this will enhance (speed) the dissipation of porewater pressure.

Badges
Science topic

Similar topics
Agriculture
Soil Science
Soil

More Navid Yeganeh's questions See All

Should the effective stresses be constant during the effective stress numerical analysis?

Assuming running the undrained effective stress analysis in FLAC3D via Config FLUID using the effective stiffness and strength parameters, are we expecting the constant effective stresses in the...

06 July 2019 8,943 3 View

How can one remove the water level from the FLAC3D simulation at some point?

Is it possible to deactivate the effect of water so that FLAC adds the amount of steady state PWP to the effective stresses in all zones such that all the stresses in the soil constitutive model...

05 June 2019 5,263 2 View

How are the horizontal stresses calculated in FLAC3D?

The very initial step of each project is setting up the in-situ stresses. Right after the said step as well as amidst the dynamic analysis, could you cast light on how FLAC internally does the...

04 May 2019 2,205 1 View

How to assign the appropriate values to the interface element properties in FLAC3D?

Hey There. I am seeking a batch of references whereby the cohesion, friction angle, and dilatancy of the interface element, e.g., between a concrete foundation and the soil mass, could be...

02 March 2019 808 3 View

In what condition is the assumption of the constant effective major stress applicable?

I was wondering what were the rationales behind making such an assumption in the soil mechanics and geotechnical earthquake engineering? Is it allowed to be used only in the static condition or it...

01 February 2019 4,073 1 View

Could you please set forth why the most of the increases in the pore-water pressure in the undrained condition would occur during the unloading?

Please find enclosed the attachment.

11 December 2018 9,455 1 View

How to elaborate the diminishment of PWP in the vicinity of a foundation in a soil-structure interaction system amidst an earthquake?

PWP: Pore-Water Pressure

09 October 2018 2,393 0 View

Where can the journal abbreviations be found?

I am wholly grateful to you if the Civil Engineering journal abbreviations source could be announced herein. TA! Navid

05 June 2018 1,185 2 View

Would you please shed light on the rationale behind the statement below?

The yielding stress of concrete material is considered to be the same as the characteristic compressive strength (fc0) of concrete.

05 June 2018 8,489 0 View

What is the appropriate distance between the side boundaries in a 3D numerical model of a soil-structure interaction system for a seismic analysis?

For instance, Rayhani and El Naggar (2008) posited that the said distance ought to be greater than five times of the superstructure width. Rayhani, M. H., & El Naggar, M. H. (2008). Numerical...

05 June 2018 536 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View