21 April 2020 1 1K Report

I have searched on PDB but I didn't succeed in retrieve ACE 2 from PDB. Does there any option to obtain this Enzyme.?

More Nazim Uddin Emon's questions See All
How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Why is my CFD problem (mini heat sink rectangular channel) not converging while having good quality mesh?

My CFD problem is having two interconnected rectangular channel, which is known as mini heat sink. I have already performed parallel flow inside of an interconnected mini heat sink. However, I...

19 February 2021 3,209 3 View

How to derive equations for a resonant buck converter with ZVS?

I am not understanding how each author is deriving the equations and the working principle. Individual authors are giving their own working principle explanation for different circuit topology....

12 February 2021 496 1 View

Who can use ATENA software to simulate three-point flexure test for reinforced concrete beams ? ?

Hi Colleagues I need a researcher who can simulate three-point flexure tests for 13 specimens of reinforced concrete beams. He would co-author a paper with me being published in Elsevier. Best...

17 December 2020 3,737 2 View

Who is expert in AANs ?

Dear Colleagues I need a co-author who is an expert in the Artificial Neural Networks ANNs to work with me on a research paper to predict the flexural strength and stiffness of a reinforced...

22 November 2020 4,483 2 View

Polyelectrolyte complex ion pairing through IR?

Is it possible to observe ion pairing (contact ion or solvent separated ion) of polyelectrolyte complexes through liquid FTIR? Although the PECs have been widely studied in the last two decades, I...

12 November 2020 4,800 1 View

How can I get better picture for the attached TEM Image??

I used TEM equipped with tungsten gun to obtain attached image (several other too, like shown). Side blotting technique followed by negative staining (1% PTA for 30 sec) was used. I cannot get the...

31 October 2020 1,902 5 View

How can I get Nusselt number for mini rectangular channels using fluent?

I am validating my CFD mini rectangular channel model. For that purpose, I need to know how to get the Nu number accurately. For Calculating Nusselt no. from fluent post-processing as follows:...

24 October 2020 3,444 5 View

What is the possible biological explanation of the mutational pressure as a driving force on the evolution of particular species ?

In one analysis major role of mutation pressure was observed in codon usage bias of some species

19 October 2020 4,755 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Dear all, I was wondering if anyone knows whether MGLtools and Autodock can run on Mac OS?

I have tried to download the 64-bit version of MGLtools however, as many times as I have downloaded and uninstall the programs, an error arises that the app needs to be updated. Thank you.

03 March 2021 5,997 2 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close