Has anyone tried to use the Duncan Chang Model for 2D model in comsol multiphysics? Could anybody send me an example? i did find it under nonlinear elastic material but could not successfully implement it.
It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...
24 February 2021 5,974 4 View
I have 6 heaters each of power 0.5 kW and mounted below a curved mild steel sheet of thickness 4 mm. The heaters and the below section is covered and insulated. I want the top surface to be...
05 November 2020 199 5 View
In what time do a protein body consumes an ATP molecule for an active process to happen?
02 October 2020 8,135 4 View
I have tried based on pixel value with a referential ground-truth temperature of some different pixel value, a region of interest (thermal image of a person's forehead ). I am getting near about...
15 July 2020 336 1 View
If I have published x no of papers as a first author and y no of papers as the second author, how can I calculate my research impact factor not considering the citation? Thank you in advance
30 May 2020 5,086 17 View
What is the electrical conductivity and relative magnetic permeability of Steel P92 material ?
25 February 2020 8,433 2 View
Is it possible to track endoplasmic reticulum and calcium present in that simultaneously by using dye? Do there exist any other alternative way ?
12 February 2020 9,022 3 View
We are checking cancer cell death by activated PBMCs in a co-culture system. We specifically want to analyze the markers (Caspases, PI3K/mTor/AKT, BAX BCL2 and several other markers) using...
30 January 2020 7,697 2 View
I am trying to simulate the deposition of Silicon over SiO2. In reality, when we try to deposit a crystalline Silicon over SiO2 (amorphous), we get rather a polycrystalline Silicon. In ATHENA...
22 November 2019 4,916 4 View
I use light protected jars and big falcon tubes to grow my plants. Usually, I don't get algal contamination when growing plants for 2-3 weeks. But, sometimes I get algal growth in my samples. It...
23 June 2019 1,993 4 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.
24 February 2021 4,150 3 View
Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.
23 February 2021 9,086 3 View
I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...
23 February 2021 4,050 1 View
Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?
22 February 2021 2,968 1 View