Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Why is the efficiency of viral mRNA electroporation in PBMC low?

Hello, I have been struggling with the electroporation of PBMC with HIV-I mRNA. Although the quality of the RNA generated is good, and the handling of the cells in meticulous, the frequency of...

27 February 2021 9,233 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How do I calculate absorption coefficient of my thin film if I dont know the thickness? Or how can I calculate the thickness of my sample?

I have done Uv-vis characterisation of my thin film and have received absorbance and transmittance data. Now I want to calculate the absorption coefficient but I dont know the thickness of my...

21 February 2021 7,148 8 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View