How can we simulate wire rope in large scale(for example 10 m) in abaqus?

Ghanbar Barzegar @Ghanbar-Barzegar

01 February 2015 1 8K Report

In many articles, the wire rope was modeled with solid element but this way needs high run time

Ghanbar Barzegar

dear saeed

are you think we model wire rope with beam element?strands with filaments?

Badges
Science topic

More Ghanbar Barzegar's questions See All

I am Extracting Streptomyces DNA with CTAB method. I would like to know When should I add RNAse in the CTAB protocol for Streptomyces DNA extraction?

I did CTAB for DNA extraction and I got good DNA IN BOTH side (Quantity and Quality) but I had RNA in my gel. I wanted to add RNAse after that and when I add it my DNA were degraded. Could you...

18 April 2024 3,595 0 View

How to write thermal creep subroutine for transient state in step VISCO?

In the creep analysis with temperature, I used the creep subroutine and despite spending a lot of time and testing simple examples to confirm this subroutine, I could not answer the transient...

06 February 2023 1,560 0 View

In a clinical trial, what do we expect the tolerability rate to be among the placebo group?

In a phase II clinical trial that assess the safety and tolerability of an investigational product versus placebo, do we normally consider a tolerability rate for the placebo group? Do we expect...

09 November 2022 1,864 3 View

How could we explain the negative correlation between IgG and IgA total titers in patients?

We just saw a negative correlation between IgG and IgA total titers in some patients. but why? how could I explain that in my paper?

01 February 2021 5,455 2 View

How can one define the modes of dispersion curve numerically?

Dear all, I am trying to find a way to find dispersion curves of plates using Rayleigh-Lamb frequency equations. I used a repetitive procedure by sweeping through the frequencies and inside it...

25 November 2020 7,476 5 View

Do you know any open clickstream dataset for recommender systems?

recommender systems, stream data

10 April 2019 291 3 View

Is there any Impact and blast standard test for materials (such as concrete, steel , ....)?

I found just charpy and IZOD test for it. I want to know other tests?

18 August 2018 3,990 3 View

How can I fit two semicircled nyquisit plot to an equvalent circuit with two resistance and 2 capacitance?

I have a Ru based electrocatalyst which I use it for Hydrogen Evolution Reaction. I have analyzed the EIS of this catalyst in the region of H-UPD and H-OPD. In more positive regions, the nyquisit...

29 June 2018 5,336 6 View

How can we extract damping ratio for the part that we have modeled in CAD?

08 June 2017 9,727 2 View

Could anyone give me damping property of steel?

i want to analyse a part and i need to know about damping property to insert and import in material module in abaqus software. the coefficient of damping for example alpha & beta are needed to...

31 May 2017 5,947 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View