How can we calculate Start of Combustion in Diesel engines,Without using HRR curve..?

01 January 1970 0 3K Report

How SOC for diesel engine can be calculated using empirical formulas? if we only have P-theta curve, mass of fuel and air. I only know SOI, now if I need to calculate SOC, How to calculate?

Badges
Science topic

More Daizy Rajput's questions See All

How can we change CC of SI engine?? Does increasing the compression ratio (by removing the plates on the head) increases the CC as well???

07 August 2016 4,601 2 View

How to decide the start of injection (Crank angle) for a gasoline engine?

How to decide the start of injection (Crank angle) for a gasoline engine? For different injector geometry, how to decide a correct start of injection.

05 June 2016 2,073 1 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

Why Orca calculations take too loong?

Hello! I am trying to calculate the sumatriptan molecule, but it has been counting for five days and it does not stop. It seems to me that it is too long and I am doing something wrong. Please...

25 July 2024 3,364 5 View

MDCI module in Orca software?

Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...

21 July 2024 1,632 0 View

Should a defect induced structure be optimized in a DFT calculation?

I'm trying to study the effects of introducing vacancy defects in my material. If I optimize my structure and find the lattice parameter before introducing vacancy, should I again optimize my...

18 July 2024 1,794 2 View

Why flow rate of MFC for pure NH3 gas decreases with time?

We have been using MFC to control the flow rate of pure ammonia gas. The MFC is placed in an oven at 50 deg. C to avoid blockage due to NH3. However, after a few days of usage, the MFC is unable...

11 July 2024 5,796 1 View

What is the recommended type of pseudopotentials for QE?

Hello dear colleagues and professors Please what is the recommended type of pseudopotentials for QE? ultrasoft or norm conserving?? And from where get all types of pseudos (us, nc, pbe,...

09 July 2024 9,541 5 View

What is the consumption of hydrogen in 60 volt and 70% efficiency in fuel cell ?

Hydrogen fuel cell

03 July 2024 7,723 0 View

What to do for Error termination via Lnk1e in /share/apps/gaussian/g16/l502.exe, for Ce through B3LYP/SDD?

I am trying for the structure optimization via Gaussian16 DFT calculation, for a system consisting of C,H, N, O and Ce atoms. Where I am using B3LYP/ 6,311G(d,p) C, H, N and O and B3LYP/SDD for...

30 June 2024 9,979 4 View