How can UV cured printed glass pieces be laminated without any delamination?

More Reuben Gol's questions See All

Is it possible that PVB interlayers can degas and alter the surface of glass edges that are not in direct contact with the PVB interlayers?

In the laminated glass industry, PVB interlayers are sandwiched between glass sheets and pressurized/heated in autoclaves. The PVB interlayers are normally trimmed as close as possible to the...

07 August 2017 4,290 0 View

What has a stronger bond with glass surfaces/edges? Polyvinyl butyral or Thermoplastic Polyurethane?

From my understanding, both PVB and TPU form a combination of Hydrogen bonds, Van der Waals forces and chemical bonds with the hydroxyl groups of the glass surface. Is it true that PVB has a...

07 August 2017 8,442 3 View

Is there such a thing as an industrial optical profiler?

I am looking for an optical profiler or something similar that can provide surface profile images for a large area of glass or multiple pieces of glass at once (around 1 m2 total at most). The...

31 December 2016 7,906 6 View

What flocculant would be ideal for removal of colloidal glass in water tank?

Through the grinding of glass edges, the glass frit is collected in the water used for the grinding machine. This water is collected and reused for grinding purposes. In order to "clean" the...

08 September 2016 4,242 1 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View