how can " behavior modeling " or " behavior engineering " ? methods and measures ?

More Dheyaa FALIH Bannay's questions See All

Good evening everyone , Is the choice of a new subject for doctoral dissertation necessary or optional for the researcher?

choice of a new subject for doctoral dissertation

05 June 2018 5,218 0 View

Hi all , "research problem" ?

It is well known that the presentation of a doctoral dissertation in the field of organizational behavior must be linked to the existence of the problem "research problem". if There was no problem?

02 March 2018 4,078 8 View

Hi all , any information about this book ?

(introduction to Mediation, Moderation, and Conditional Process Analysis A Regression-Based Approach ) , Andrew F. Hayes,2013

11 December 2017 3,578 3 View

Hi all , any information about this book ?

(introduction to Mediation, Moderation, and Conditional Process Analysis A Regression-Based Approach ) , Andrew F. Hayes , 2013

11 December 2017 5,282 0 View

Hi all, do you have an idea of my question?

What do the following terms mean: - An analytical study - Exploratory study - Survey study Can these terms be combined into one search?

10 November 2017 10,003 1 View

Hello everyone Specialists in Organizational Behavior Can they work in companies?

Except teaching at universities, as the answer was yes, what is the name of that job in companies?

08 September 2017 9,759 1 View

Good evening, everybody

What is the difference between study and research?What is the difference between survey and analytical study? What is a master's thesis and a doctorate, research or study?

07 August 2017 4,438 3 View

Is the study of management, leadership and organizational behavior important in the business world today?

dear all, Today's world is witnessing a lot of rapid changes from different cultures, confrontations and behaviors. Can these developments be kept up to date with the methods we have learned at...

06 July 2017 9,904 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View