How can one get the current density and charge (Q) from I-t curve (chronoamperometry) in electrodeposition?

09 September 2013 1 6K Report

From chronoamperometry how to calculate charge flow?

Integrating I-t curve up to any point t should yield the total charge flow up to that point in time. If surface area of electrode is known, then J= I/A.

Badges
Science topic

More Rekha Bai's questions See All

What type of materials doping is possible to enhance the conductivity of cadmium selenide (CdSe) films by electrodeposition?

As-deposited CdSe films have very high resistance.What materials doping can be used to increase the conductivity?

01 February 2015 9,954 7 View

How to prepare the solution for ternary CdSexTe(1-x) thin films??

Can anyone explain in brief how to prepare the solution for ternary CdSexTe(1-x) thin films e.g. CdSe(0.6)Te(0.4) thin film?

09 October 2014 9,993 2 View

How do PbS nanoparticles in CdSe matrix lead to better absorption in solar cell?

How solid solution of CdSe/PbS leads to optimum band gap?

08 September 2014 7,385 2 View

Can anyone suggest a reference electrode for electrodeposition?

Can anyone suggest a reference electrode for electrodeposition in aqueous solution? Which one is better between a Saturated Calomel Electrode (SCE) and an Ag/AgCl reference electrode?What is the...

03 April 2014 9,953 22 View

Can anyone help with the deposition of ZnO/SnS heterostructure by electrodeposition?

How much feasibility of electrodeposition of SnS layer on electrodeposited ZnO nanostructures to form the ZnO/SnS heterostructure? What is the future scope of this type of heterostructures for...

03 April 2014 4,110 5 View

Please can someone suggest an Indian manufacturer of Reference electrodes (e.g. SCE,Ag/AgCl etc.) for the purpose of electrodeposition?

Ca anyone suggest some Indian manufacturers of reference electrodes e.g. SCE or Ag/Agcl for electrodeposition purpose in aqueous electrolyte. I have references of some companies outside from India...

03 April 2014 4,342 1 View

Can anyone suggest a good reference electrode for electrodeposition technique?

I want some information regarding reference electrodes e.g. SCE or Ag/AgCl of various companies and of which supplier should be in India and cost should be less than Rs.15000.

03 April 2014 4,641 3 View

How can we decide the thickness of absorbing layer in thin film solar cell?

On which parameters does the thickness of absorbing layer depend?

31 December 2013 1,433 3 View

How can we trap more light in nanostructures than thin films in solar cells?

Light trapping.

31 December 2013 4,548 1 View

Can anyone tell me why the band gap of the material for high efficiency solar cell should be around 1.5eV?

31 December 2013 7,347 5 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Is there a good freeware software for photodocumentation of TLC?

I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?

31 July 2024 8,415 1 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

How to determine the charge passing during a cyclic voltammetry?

Dear All, here is my question: if I have a 15-scans cyclic voltammetry performed with PalmSens, how can I obtain the charge passed during the process? Hopefully avoiding integrations,...

29 July 2024 3,733 5 View