How can I use FSI+Piezoelectric module in COMSOL Multiphysics?

More Lucas Goulart Duarte's questions See All

[COMSOL 5.1] Simple FSI simulation not converging. Can someone please take a look at my model?

Hello, I'm a newbie on CFD and starting to learn how to use COMSOL. I tried to modify one example from COMSOL but it isn't working. I think it has something to do with Inlet velocity, but i...

03 April 2019 3,665 4 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

No streamlines present in a small region inside a flow. This means exactly what?

No streamlines present means whether the flow is getting obstructed there and the velocity inside the region is zero? Or else, the fluid is trapped inside that region with a nonzero velocity?...

22 February 2021 5,249 10 View

Saad Najeeb

Good work.

Hamidreza Ahmadi Moghaddam

Dear Lucas,

I did a project sometimes back which I believe is very close to what you want to perform right now in ANSYS and published the work in ASME PVP conference. It is a numerical simulation that involves structural-thermal-electrical analysis in conjunction with FSI. Reading this article may help you a bit since the simulation is done in ANSYS and not in COMSOL.

Yes, you can simulating it using ANSYS-Fluent Ver. 15