Is there a tool for 3D miRNA modeling?

For example for an interaction study between a protein target.

22 November 2020 3,952 4 View

New network testing models for deep learning in biological testing ?

We tested four models: logistic regression (LogReg), multilayer perceptron (MLP), graph convolutional network (GCN), and edge-attention graph convolutional network (EAGCN). Are there other models...

08 November 2020 2,347 4 View

In which dry organic solvent/solvent mixture molten 1H-imidazole could be precipitated at 100%?

I am trying to isolate an allkylated imidazole from a mixture containing unreacted 1H-imidazole. The problem is that imidazole is slightly soluble in my targed molecule. Furthermore, I need to...

04 November 2020 4,513 3 View

Bioinformatic tools to determine ploidy in microbial genomes?

Looking for tools with proved accuracy to detect ploidy levels in microbial whole-genomes.

14 October 2020 4,273 3 View

Where to find cancer datasets composed by clinical markers and gene expression levels?

Currently, I am validating a new machine learning approach. But, I need to find different cancer datasets composed by clinical markers and gene expressions. For now, a just found MMRF data set...

11 October 2020 9,012 2 View

Can I use a Glass electrode (standard used for pH measurement) for measuring ORP?

I have made a test to investigated: I measured the potential in mV of a standard +220mV solution using my pHmeter which gives a mV value with the pH. The result was +9mV. But this was the result...

06 October 2020 7,220 3 View

How to do validation on a new instrument?

Halloo scientists, please help me the procedure s on doing validation on new bought instrument/equipment before starting doing analysis

07 September 2020 1,590 3 View

Can my RNA interference have any influence in my endougenos control gene?

Good night all. I'm using RNAi to knockdown a transcription factor from a primary cell and I need to validate by westernblot. With Ponceau marking i can see that i'm putting the same amount of...

25 August 2020 263 3 View

How can I hide nodes with posterior probability under 0.5 in BEAST phylogenetic tree visualization?

06 July 2020 1,376 6 View

How do I stored nano particles in my workplace and how long?

I am looking for a technique which is used to store the nano particles without any property change.

23 June 2020 2,473 15 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

No streamlines present in a small region inside a flow. This means exactly what?

No streamlines present means whether the flow is getting obstructed there and the velocity inside the region is zero? Or else, the fluid is trapped inside that region with a nonzero velocity?...

22 February 2021 5,249 10 View