How to remove paraffin from lithium metal?

Because of high oxidation potential of lithium, this material has been put in paraffin solution. How can i remove paraffin from metal for Li-S battery assembling?

07 August 2017 5,712 2 View

What is physical vapor transport?

what is physical vapor transport system? I want a sample of this system for producting.

09 October 2014 5,530 0 View

Why are our thin film layers in various deposition conditions amorphous?

We are working about influence of optical, electrical and structural properties of AlN thin film under various deposition conditions. We deposited AlN on the quartz substrate under 100,300,400...

07 August 2014 8,208 6 View

How can obtain Transmission spectra from absorption spectra with UV-VIS spectrophotometer?

I have absorption spectra for AlN thin film, I want to obtain transmission spectra from it theoretically. Is It possible?

06 July 2014 1,579 2 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View