How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Dear Colleagues, I am looking for a way to dop of electrospining nanofibers on the HEPA filter.Someone can guide me?

Electrospining method is important for production of nanofiber .If doped with nanoparticles ,can be used for remove of contaminant such as VOC , but don't have mechanical strengh . For finding a...

24 January 2021 7,290 3 View

What is the current situation in the development of nanofibers laminated and biodegradable material based facemasks?

I want to know the progress in the development of polymer laminated, biodegradable material based facemasks.

18 January 2021 9,205 3 View

What could be the appropriate load and loading rate to carried out nanoindentation for testing microhardness of nanofiber?

Dear Reader, Recently, I have prepared a polymeric nanofiber using PVA polymer doped with some nanoparticles and I want to find out its microhardness. So, I was planning to do...

09 January 2021 4,452 7 View

Why the bandgap of CH3NH3PbCl3 films are different for spin-coating method and electrospinning method?

The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?

08 January 2021 5,646 6 View

How can I take an electrical conductivity test from a nanofibrous scaffold?

I have a nanofiber scaffold for tissue engineering. When I did the electrical conductivity test, the ohmmeter reports a wide range of values (from 300 kOhm to 20 MOhm). I placed the scaffold...

06 January 2021 2,232 1 View

DSC test- Glass transition temperature of the electrospun PA66 nanofibers?

Hello Everyone, I did several DSC tests on the electrospun PA66 nanofibers to obtain the glass transition temperature. According to the material datasheet, the Tg point of PA66, as cast, is around...

13 December 2020 1,506 2 View

How do I avoid sucking up electrospun scaffolds during cell culture?

Hi, I'm a PhD student working to develop electoconductive, electrospun scaffolds for cardiac tissue engineering applications. I have been seeding cells onto these scaffolds but having major...

04 December 2020 6,672 3 View

Does crystallinity degree, (and crystalline phase) of a polymer affect its surface energy and adhesion?

I have several PLLA electrospun nanofibers with different crystallinity degrees and also different crystalline phases and I am measuring the adhesion force by AFM-based techniques. I wonder if we...

28 November 2020 3,269 5 View