How can i make irrigation scheduling simulation model using GIS ?

Noha Abdulwarth @Noha_Abdulwarth2

01 January 2013 0 7K Report

What are the tools or analysis in gis may help me to make this model?

Are there any useful tools beyond archydro & hydrology?

Badges
Science topic

More Noha Abdulwarth's questions See All

Is there any tool in ArcGIS or model to simulate water flow at open canals?

I want to simulate water flow at open canals and irrigation water networks in ArcGIS Is there any tool help me?

09 October 2013 690 41 View

How to know the available water holding capacity of clay soil?

I'm developing a model for irrigation water scheduling and the soil texture of study area is clay but it varies from one region to another. There is no chance to take samples but the properties...

04 May 2013 2,449 15 View

Is there any software or model for evapotranspiration calculation?

I'm looking for a software or model to calculate evapotranspiration. The type of the output should be excel spreadsheet or database . Is there any tool to calculate evapotranspiration in ArcGIS ?...

04 May 2013 757 87 View

How to calculate the percentage of green spaces in remote sensing image using erdas imagine?

04 May 2013 4,285 6 View

Can anyone help me in using Arc Hydro?

I am a beginner in using Arc Hydro - when using the DEM Reconditioning tool, the tool process failed. The results and error message are shown on the attachment, can anyone help me solve the error?

01 February 2013 6,542 3 View

What are the GIS tools that can help me in water distribution in canals and fields?

01 February 2013 7,814 2 View

How to calculate evapotranspiration during one season?

01 February 2013 10,055 22 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View