How can i make irrigation scheduling simulation model using GIS ?

28 January 2013 0 7K Report

What are the tools or analysis in gis may help me to make this model?

Are there any useful tools beyond archydro & hydrology?

Badges
Science topic

More Noha Abdelwarth's questions See All

Could GSH level be more in CCL4 rats than negative control rats?

i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....

26 July 2024 1,887 0 View

How i calculate Mean death time for avian influenza?

I study pathogenesis in different animal and i have mortality i need the equation

11 June 2023 170 3 View

How to calculate the relative gene expression for siRNA?

I have a results from qpcr experiment for siRNA after transfection, how to know the effect of siRNA in Knock down from qpcr results

10 June 2023 9,649 2 View

Does chloroform dissolve PVDF?

I need to know the conditions of dissolving PVDF in chloroform.

29 April 2023 401 0 View

What is the best buffer used in liver homogenization for measuring antioxidants and oxidative biomarkers?

what is the best buffer used in liver homogenization for measuring the following 1-total antioxidant capacity 2- reduced glutathione 3- nitric oxide 4- MAD 5- SOD 6- CAT I want to know the amount...

27 March 2023 5,856 1 View

Deville process for sodium metal production?

Dear all, I would like to have detailed information about the Deville process which was the first used for sodium metal production. From literature I found only data related to aluminum metal...

12 October 2022 2,887 1 View

What does "undetermined" CT values means in q-PCR?

I am measuring the gene expression of my target gene DDX43. I took 2.5 ul of cDNA for Q-PCR. I am using SYBR GREEN for my q-PCR. The concentrations of RNA for most samples were 20-60 ng/ul. The...

10 August 2022 6,401 5 View

CDNA stability in room temperature??

I sent CDNA from to japan . It take more than 10days to reach the lab . Is this will effect on CDNA quality

01 May 2022 4,699 1 View

Why HSQC and HMBC for iron carbene complexes are not good and have many dots in the whole spectra?

Hello, I have an iron carbene complex that form aggregation. When I used CDCl3 for HNMR, peaks were too broad, but when I used deuterated MeOH, I got a sharp peaks; however, the HSQC and HMBC were...

27 October 2021 7,406 5 View

What is the role of sodium acetate in acetylation of primary amine with acetic anhydride?

i want know the role of sodium acetate in the acetylation of primary aromatic amine using acetic anhydride. the reaction mechanism doesn't explain it.

04 May 2021 9,783 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View