How can I make a surface from several surfaces in catia?

Kazem reza kashyzadeh @Kazem-Reza-Kashyzadeh

27 February 2016 1 613 Report

I have a model that created by multi surfaces in Catia software. but, i want to make one surface by using multi surfaces.

who can advise me ?

Yuri Mirgorod

Dear Kazem:

Any powders of nanoparticles, microparticles compared parameters characterize a specific surface area in units of cm2 / cm3.

Regards

Badges
Science topic

More Kazem reza kashyzadeh's questions See All

If the emission of all greenhouse gases is stopped now, will the temperature of the earth continue to rise?

Here's a serious question: If we were to stop emitting all greenhouse gases right now, would the Earth's temperature start to cool down, or would the existing greenhouse gases continue to warm the...

30 July 2024 5,123 4 View

How to prepare 100ml solution of 2.5% Glutraldehyde in 0.1M PBS(phosphate buffer) pH about 7, from 25% Glutradehyde and 1X PBS?

final solution volume is 100ml

03 June 2024 417 0 View

How can i use hexamethyldisilazane(HMDS) for drying instead of Co2 and freez drying for SEM analysis of rice anther and pollen?

could you please help with a protocol? should i do it directly on the aluminium stub after dehydration with 100% alcohol or not? should i release the pollen or whole anther is better and dehisce...

03 June 2024 4,793 8 View

What is the best method to enhance the surface hardness of cutting tools made from SPK steel?

SPK tool steels are used for cutting wires made from low carbon steels. We are searching for a cheap and effective method for increasing the cutting characteristics of the cutters.

14 May 2024 4,948 0 View

Constant Reciprocal of Step Size?

Hello I recently encountered a problem with the reciprocal of step size plot in Comsol Multiphysics. After a certain time (seconds) in a time-dependent solver, the plot oscillations will be...

04 May 2024 7,278 0 View

Poor viability of T cell after transduction with CAR Lentivirus!?

Hi everyone I produced a batch of virus , enriched it with centrifugation, and titrated it with T cells after 48h. For my experiments I want to use MOI 3 and that's equal to 1/12 dilution. but at...

02 May 2024 9,727 3 View

Are you interested in submitting papers to a new journal called "InfoScience Trends"?

InfoScience Trends offers comprehensive scientific content that delves into various facets of information science research. This includes but is not limited to topics such as information...

26 April 2024 9,521 1 View

Does the color of pan traps affect the sampling of flies from the superfamily Bombylioidea?

Garret, 2020 used traps of blue, yellow, and white colors for sampling and collected several specimens.

06 April 2024 6,995 2 View

Laboratory procedures for identifying the concentrations of formic acid and acetic acid in aqueous solutions???

What are the laboratory procedures for identifying the concentrations of formic acid and acetic acid in aqueous solutions using titration, spectrophotometry, or gas chromatography methods...

06 April 2024 187 3 View

Is it possible to produce a very small amount of volatile oil along with condensed gas? If so, could you please provide a real example?

Is it possible to produce a very small amount of volatile oil along with condensed gas? If so, could you please provide a real example? Thank you.

04 April 2024 1,411 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View