How can i make a graphene sheets on both sides of the nanotube?

Meisam Karimi Rad @Meisam-Karimi-Rad

12 November 2019 1 10K Report

I wanted to know, how to make graphene sheet on both sides of a carbon nanotubes in VMD software ?

Meisam Karimi Rad

Thank you so much julie

Badges
Science topic

More Meisam Karimi Rad's questions See All

I need dataset for recommandation system?

Hi every body I need to collect datasets from different source to work on recommendation system algorithms, could you advise me how collect data?

27 February 2021 7,063 7 View

Hey guys, I'm looking for an efficient protocol to transfect patient-derived tumor cells with a high rate of transient transfection?

As you know it's quite tricky to get primary cells transfected at a relatively high rate!

31 January 2021 3,580 4 View

What would be the best option to dock a number of peptides to a protein?

I have been using PyRx to dock peptides to a protein. Initially the numbers were small so it was okay. But now I have to dock over 500 peptides and doing so manually would take forever. My...

10 January 2021 3,330 4 View

How can help me to Convert the files DIgSILENT PowerFactory example to an earlier version (v15.1.7)?

Hello , How can help me to convert this example files Power Factory version ,The files example from the DIgSILENT website has been created with version 15.2.5 which I do not have access to. I'd be...

31 December 2020 4,213 1 View

How to build .cks file (chemkin file) in ANSYS-Forte for hydrogen-diesel dual fuel?

Dear all, I'm trying to simulate the combustion of hydrogen diesel in dual fuel mode in ANSYS-Forte. I have kinetic reaction mechanisms file( .txt) but in order to build the .cks file in the...

28 December 2020 1,570 3 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

What is the effect of drought and silicon stress on soil pH and EC?

15 November 2020 3,971 5 View

How can I fix the `engine error` with no error message in Lumerical DEVICE software when it only shows directories instead of error message?

When I run my simulation in Lumerical DEVICE, it shows an error entitled `engine error` after reaching the simulation to 100 percent. When I right-click and chose 'job details`, it only shows the...

22 October 2020 4,973 1 View

What are the effect of data spread on Random Forest model performance?

Since I am using the Random Forest model in R to predict LST (land surface temperature) from actual LST, I realized that model performance is better in lower Average LSTs, thus I wanted to extract...

14 October 2020 9,278 2 View

How to visualize hydrogen bonds in water usingVMD?

I want to visualize Hbonds between water molecules in the water using VMD. I use Hbonds in create representation but cannot see the bonds in the 3d view. Any idea? I play around with cut-off...

13 October 2020 2,610 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

How to find out the problem of VMD software when i run it?

Hello I try to install and run the VMD software on windows 10 (64-bit).It doesn`t work and it is closed when I run it. I checked all of tutorials, videos and documents. But they did not work...

22 February 2021 8,211 3 View