How can I made a composite material of type Ceramic matrix composite in Ansys workbench ?

Amirhosein Poureshagh @Amirhosein_Poureshagh

04 March 2022 0 1K Report

I want to simulate the failure ceramic scaffold under load-bearing in Ansys workbench and my material is a composite of type CMC for example alumina / graphene composite.

how can I made this material in Ansys workbench ??

Badges
Science topic

More Amirhosein Poureshagh's questions See All

Graphene oxide loss may be due to low gas flow?

Hello dears, I had a scientific question I 3D printed a hydroxyapatite scaffold containing graphene oxide And then I sintered this inside the controlled atmosphere tube furnace (argon gas) at a...

11 July 2023 4,478 2 View

I need to composite graphene oxide with a ceramic powder and sinter it at 1300 degrees under vacuum and argon gas. Does graphene oxide disappear?

Hello, for a research project, I need to composite graphene oxide with a ceramic powder and sinter it at 1300 degrees under vacuum and argon gas. Does graphene oxide disappear?

24 February 2023 8,830 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Can we find a statistical matrix mechanics equivalent to the Schrödinger equation?

We assume that we can find a statistical matrix mechanics equivalent to Schrödinger's PDE in two consecutive steps: i-Transform the Schrödinger PDE describing the wave function Ψ into its square...

27 July 2024 3,959 4 View