Orbitrap Fusion FT keep getting disconnected?

Hi, I been having a problem with the Orbitrap Fusion for quite a while and it has been getting more and more frequent, which is very frusttrating. The fusion FT would get disconnected suddenly...

22 January 2021 1,235 4 View

What is the basis set to optimize ZnO using GaussView for DFT calculation study?

Greetings, I have a bit of problem in setup the basis set of my DFT study for ZnO.. As you can see in the image attached below, I use B3LYP 6-31G (d,p) for geometrical opt. of ZnO.. But sadly, I...

13 January 2021 7,508 4 View

How does titanium dioxide (TiO2) as a coating's component enhance the coating performance in terms of anticorrosion??

Greetings, Recently, I was asked by a researcher how does TiO2 enhance the coatings polymeric structure making it able to reduce corrosion reaction by preventing the penetration of aggressive...

02 January 2021 5,257 5 View

What are the suitable amplitude of sinusoidal perturbation signal to analyzed stainless steel 316L?

Greetings researchers, I want to ask for your suggestion in regards to what is the suitable amplitude of sinusoidal perturbation signal to analyzed the conditions of bare and coated stainless...

07 December 2020 7,699 7 View

How to improve DNA extraction using TRIzol and chloroform?

02 December 2020 1,919 1 View

What is the solubility of crude extract of plants in water?

Greetings all, To my limited understanding, the crude extract of plants obtained using solvents such as ethanol and methanol are usually insoluble in water. Is this correct? If it is soluble in...

02 December 2020 1,024 6 View

Does the concentration of the fluorescent compound affect the fluorescent reading on a 96-well plate?

I am trying to detect the fluorescent level of the extracted RNA sample on a 96-well plate. After extraction, I dilute the RNA sample in 20ul solvent. Can I load the 20ul RNA sample directly to...

30 November 2020 2,616 2 View

Any available international research grant in this COVID-19 year?

Dear researchers, I am a researcher from a university in Malaysia. I know that we all are having a tough situation in this pandemic year. I just posted this to know if there is any possible...

24 November 2020 8,759 3 View

In your opinion, what are the mechanism performed by corrosion inhibitor in a coating for corrosive medium?

Greetings researchers, There are quite a number of studies has been performed to analyze the effects of corrosion inhibitor when incorporated in a coating (epoxy, alkyd and etc) for the...

23 November 2020 6,622 10 View

For a marine coating, how much does its mechanical strength needs to be?

Greetings to all researchers, First and foremost, I would like thank all of you for answering this question. So, my question is quite general I guess, for a standard marine coating with good...

08 November 2020 8,880 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View