How can I get data for yield stress and plastic strain for ABS in ABAQUS? and is it possible to do motion and extrusion simulation simultaneously ?

07 July 2019 1 2K Report

Hello, I'm doing extrusion simulation and for that I need yield stress and plastic strain. if possible then related to its temperature. 2) is it possible to do motion and extrusion simulation simultaneously ?

Farshad Abbasi

Try the following link:

https://classes.engineering.wustl.edu/2009/spring/mase5513/abaqus/docs/v6.6/books/usi/default.htm?startat=pt03ch12s08s02.html

Badges
Science topic

More Jay Prajapati's questions See All

How to do CFD simulation in Abaqus 2018?

I want to do plastic simulation. I have assigned Solid section and this is my element. C3D8T: An 8-node thermally coupled brick, trilinear displacement and temperature. I already got some result...

06 July 2019 3,964 11 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View