what is the right monomer?
particle size of powder?
Agar can be used for this purpose.
Dear Imad,
what about isobam? isnt it a proper choice?
which particle size distribution do you suggest? can you explain me from beginning to the end( all required steps and conditions)?
there is portable carbon steel container of 98% H2SO4 at 90°C. what is an appropriate coating or lining for prevention corrosion in this case? what do you think about rubber lining? also vapor of...
05 June 2019 1,984 4 View
there is an extractive metallurgy reactor and its core is in 1000°C. there is some heat supplying flames around the core and i want to apply refractory materials around them for the purpose of...
05 June 2019 9,321 4 View
Im interested into spark plasma sintering of tungsten carbide powders an production of different segments via this. its gonna be my PhD thesis subject so it has to have innovation and should be on...
04 May 2019 5,227 1 View
cladding or lining or coating or .....
03 April 2019 9,849 6 View
a complete book or review paper on carbon and graphite.
03 April 2019 6,926 4 View
what are the forming and shaping methods of graphite and also fused quartz powder?
01 February 2019 7,619 3 View
does presence of water in 38% acid makes any differences? temperature is the same.
11 December 2018 4,873 1 View
Can it resist dry HCl at 60 °C ?
09 October 2018 3,397 2 View
Im confused because some references take anhydrous hydrogen chloride as a corrosive gas but some of them take it neutral. if it is corrosive, what materials can resist high temperature corrosion...
09 October 2018 4,285 8 View
does it gel automatically after mixing with water and ceramic powder?
08 September 2018 6,433 0 View
I got these smeared bands quite often lately. We typically run the gel at 140V with a 10-12% gel and do a wet transfer at 220 mA for 1.5 hr in cold room. We also noticed some dirty spots/dots (see...
10 August 2024 7,480 3 View
I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...
06 August 2024 3,130 2 View
I am having an issue with my gel image where my PCR product is not appearing very bright on the gel. When I perform gel extraction, the A260/280 purity value is very low. I used the Qiagen gel...
05 August 2024 9,798 3 View
average particle size calculation from TEM
04 August 2024 2,921 1 View
TEP presentation caption (The Environmental Project) Re: Why should Washington’s DC, or any country government point of location think of as nowadays of as to being 'tomorrow as to come! if it...
03 August 2024 2,484 1 View
Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You
02 August 2024 3,615 1 View
I am following Hainmueller, Hopkins, and Yamamoto's (2014) paper for my randomized conjoint experimental data analysis. The link to the paper is provided below. I received a comment from the...
02 August 2024 4,406 0 View
The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.
31 July 2024 10,109 3 View
Hello everyone, I performed a PCR yesterday, and the results showed no bands on the gel. Of course, I probably missed some crucial steps, like adding my samples to the PCR strips themselves, for...
31 July 2024 2,406 6 View
We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...
30 July 2024 942 2 View