How can I find basic information about turboexpanders?

More Masoud Mohammadian's questions See All

Thermally fully developed flow in ducts?

Hello dear friends Can we assume thermally fully developed flow for a flow in a duct with constant wall temperature? It is assumed there is transient energy equation that means temperature varies...

02 March 2018 2,046 1 View

Thermally fully developed in internal flow?

Hello dear friends What is the conditions that we can assume that we have thermally fully developed flow for both laminar and turbulent flows? I mean can we assume that we have thermally fully...

10 November 2017 8,996 8 View

Finned channel VS. simple channel?

Hello dear friends There is two channels that one of them is finned and another one is simple and without fin(as attached file). The fluid mass flow rates and inlet fluid temperatures in both...

10 November 2017 5,630 7 View

Energy equation with periodic boundary condition?

Hello dear friends What is your idea to solve energy equation analytically in a channel with cyclic boundary condition along the channel that its amplitude is variable? Is it doable?(Please find...

09 October 2017 9,054 7 View

Borehole Wall Temperature?

Hello dear researchers How can I calculate ground temperature and after that how can I find temperature distribution along borehole wall? kind regards

02 March 2017 2,204 0 View

Solving Partial Differential Equation(PDE)?

Hello dear friends I have a PDE problem(attached file) with its boundary and initial conditions. Could you please give me your opinion and methods about solving it?

02 March 2017 2,463 53 View

Solar irradiatio calculation problem?

hi friends The attached file is MATLAB code for solar irradiation on tilted surface. Why for latitude=60 and surface angle=60, total irradiation at the night (e. g. 1 or 2), is positive but it...

31 December 2016 9,994 0 View

Neural Network-MATLAB?

Hi I did my NN project and target and output results were close to each other but when I calculate Output=W2*(TANSIG(W1*X+B1))+B2, that X is my input, then output is not equal to target. Please...

09 October 2016 9,991 1 View

Any suggestion on the pressure and velocity Probe situation?

what should be the flow situation for locating pressure and velocity probe? I mean what should be the boundary layer situation for having the best place to locate these probes? regards

01 February 2015 5,464 5 View

Can anyone help with a problem in ANSYS ICEM?

I have modeled my geometry and blocked it in ICEM as attached file. The problem is that I cannot have a good meshing since determinant 2*2*2 says.

04 May 2014 3,392 12 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

What is the acceptable p-value cutoff for GO enrichment analysis ?

I have an RNA-seq data that I have analysed using Limma-voom and have extracted the gene IDs, log2FC and the p-values. At p value < 0.05, I have over 10,000 DEGs, however, when I run the GO...

31 July 2024 225 2 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

Sayantan Mukherjee

yes ,This attachment will help you.

Also you can refer the book :Turboexpanders and Process Applications

By Heinz P. Bloch, Claire Soares.

http://books.google.co.in/books?id=Z-RY1Emx4JwC&pg=PA248&lpg=PA248&dq=turboexpander+blade+design&source=bl&ots

Janamejay Singh

Plz see another link

http://books.google.co.in/books?id=18joxalFOwQC&lpg=PP1&pg=PR7#v=onepage&q&f=false

Md. Washim Akram

You may get some basic information about terboexpanders from the following attachments.