How can I fit a second-order (quadratic) metamodel on my Input/ output data in RSM?

In the second phase of Response Surface Methodology, using the central composite design on input/ output data, I want to fit a second-order polynomial on the subarea to find the optimum...

01 September 2020 8,597 3 View

Why a pair of primers give different melt curve in same DNA concentration ?

Hi everybody I'm trying to genotype two SNPs with HRM. one of them(SNP1) is set up but the other one(SNP2) shows different melt curves in DIFFERENT temperature(some samples in 92 C ,some in 86 C...

20 February 2019 157 2 View

Adjusted R-squared and partial Eta squared comparison?

31 October 2018 4,823 6 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

How can extract ciprofloxacin hydrochloride disolve in water er to organic solvent such as dichloromethan or any other solvent?

I need a procedure to extract the ciprofloxacin hydrochloride from aqueous solution by using dichloromethane in detail,. I thank you very much.

01 March 2021 4,306 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Which bacteria are suitable for quorum sensing screening?

I want to find a quorum sensing inhibitor from plant extracts. Klebsiella pneumoniae, Moraxella catarrhalis, Staphylococcus aureus, and Streptococcus pneumoniae. I looked for these strains...

01 March 2021 7,675 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View