How can I design a CNT in Ansys or Abaqus?

More Hana Gheisari's questions See All

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

DNA extraction from clinical sample of Staphylococcus aureus?

Salam everyone, So I am trying to extract DNA from isolates of clinical samples of staphylococcus aureus, I am using a QIAamp UCP kit. I followed the same manufacturer protocol and used Qubit to...

03 July 2024 3,892 1 View

Plant extract sterilization???

Dear researchers, I've been working on aqueous plant extract sample, then I autoclaved them in 10 min to sterilize and added some preservatives. However, some of them showed bacterial and fungal...

11 June 2024 1,040 2 View

Editora Artemis, Editorial Académica Española: Predatory publishers?

Hello, On the basis of the conferences I have attended, I was contacted first by Editorial Académica Española to publish a book with them (a development of a conference paper), so I would like...

09 April 2024 1,751 3 View

How to eliminate a recurring mold contamination in the CO2 incubators?

Dear researchers, We are struggling with neverending mold contamination in all of our CO2 incubators. In the past, we used to do H2O2 decontamination/24hr-UV mode every two months now we do it...

04 January 2024 3,717 4 View

How can we improve the sonication process to achieve homogenous fibrils of the desired length (<= 50 nm) as indicated by Dynamic Light Scattering?

We conducted Dynamic Light Scattering (DLS) before and after sonication of our preformed fibrils of alpha-synuclein (aSYN) using a microtip sonicator. Our protocol was as follows: Amplitude:...

10 December 2023 2,768 1 View

How to statistically analyze species diversity more than two communities?

Dear coluegues, I want to analyze, parkland woody species diversity along agro ecology (low-land, midland & highland). how can I check if there is a significant difference along agro ecology...

06 October 2023 9,369 1 View

What are the problems of separating imprisonment and what are the solutions?

21 September 2023 299 0 View

Can I create a new sort of Research Item?

Hi, I would like to create a new sort of Research Item (namely workshops, some with video links). Is that possible? Or it should be better included in "Presentation"? Thank you, Hana

21 September 2023 8,926 2 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Engr. Tufail

This guy in the yt playlist have explained it; https://www.youtube.com/watch?v=2jLY191dFm4 however if you have any question regarding modeling it in ABAQUS, connect with me on WhatsApp https://wa.me/+923440907874 and i will answer them.

Hana Gheisari

I have already seen the YouTube link you sent, but it examines CNT in composites, but I only want to examine the CNT structure itself, which is considered as spaceframe analysis. Do you have information in this field?