What is the best software to carry out Thermal-FSI simulation?

You know for example, the couple between ANSYS and FLUENT is very common for Thermal-FSI simulation. Is there any software for carrying out all process of Thermal-FSI only using one...

11 December 2019 4,803 6 View

No title

I would like to know detail information about cerebral blood flow and metabolism for designing the gene therapies for diseases of the central nervous system.

06 July 2019 6,054 5 View

The attached file is the NEW Journal Impact Factor 2017: Released in June 2018. Does anyone have the file of 2017 JCR ranking for each journal ?

.?

07 August 2018 6,861 2 View

Which two software of ADINA and ABAQUS are better for fluid structure interaction (FSI) simulation?

Which two software of ADINA and ABAQUS are better for fluid structure interaction (FSI) simulation?

07 August 2018 7,409 26 View

Can the zero-pressure (0 Pa) be used as inlet or outlet boundary conditions in the simulation of a FSI problem?

We khow that zero-pressure (0 Pa) is a very common inlet/outlet boundary condition in CFD simulation. However, can the zero-pressure (0 Pa) be used as inlet or outlet boundary conditions in the...

07 August 2018 5,256 3 View

How can I model the chip removal during bone drilling in FEM simulatin using ABAQUS or 3D DEFORM or ANSYS softwares?

07 August 2018 9,813 8 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View