I am trying to model reinforced frame section in 2D using tno diana fem software. How can I define detail reinforcing of X-section in 2D model in TNO DIANA?
If you want to use perfectly bonded elements I would suggest looking at the information on embedded reinforcements.
https://support.tnodiana.com/manuals/d942/ElmLib/node451.html
https://dianafea.com/DIANA-Tutorials
I have a biomass with given ultimate and proximate analysis data. I am using Aspen plus for the simulation of gasification of biomass. In experimental data the gasifying agent air flow rate is...
18 June 2024 2,743 1 View
i am doing a project on gasification. during pyrolysis i got the following error: * WARNING COMPONENT 'BIOMASS' IN SUBSTREAM 'NC' HAS ZERO FLOWRATE IN THE OUTLET STREAM. FRACTIONAL...
18 March 2024 6,025 1 View
I am looking for the paper or the persons who worked on cloning of short sequences targeting the different cellular organelles (vacuole, mitochondria, plasma membrane, septum) in plant pathogenic...
11 March 2024 1,878 0 View
Dear all, I am doing a gasification of biomass. In the pyrolysis section i have used RSTOIC for the devolatization of the biomass. i have specified the yield from the RSTOIC. it gave me the...
19 February 2024 8,026 0 View
What is the difference between Mixed Methods and Triangulation Methods?
12 February 2024 9,962 3 View
I am working in validation and qualification of new HPLC method. Your insights and feedback are greatly appreciated.
02 December 2023 8,514 4 View
While testing the mediation via Process Macro in SPSS, I obtained that my Total Effect is significant, Direct Effect is also significant, but My Indirect effect is not significant. In this case,...
23 September 2023 6,641 1 View
Hello, i am going to write my dissertation and i am confused in review of literature and discussion part. Please tell me what is the difference in between them.
04 September 2023 4,969 4 View
Hi, I wanted to do mode analysis of two coupled silicon waveguide separated with 200 nm with the dimension of 400 nm and thickness 0.215 nm. What should be the height and width of cladding? I...
28 June 2023 7,646 3 View
Please provide some insights on it. When calculating Rmsd from PyMol it shows "atomic alignment failed (mismatched identifiers?)". How to solve this?
20 June 2023 1,016 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Hello experts, Does anyone know any free software about retention index prediction ?
08 August 2024 7,403 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
Molecular docking software/ websites?
02 August 2024 8,704 7 View
Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...
31 July 2024 3,913 6 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
I created a file with my outgroup and ingroup species using Beauti, ran it in BEAST, viewed it in Tracer, and then used TreeAnnotator to create a file that I imported into RASP. Could someone...
28 July 2024 2,979 1 View