I am going to define an inverse polynomial (quadratic) model in "Fit Model" platform in JMP. How can I do it? I am using 30-days trial version of JMP.
Hi,
Check it here
http://www.public.iastate.edu/~vardeman/book_site/jmp/fitting_polynomial/fitting_polynomial.html
Hi
Please see the pdf in this link: http://support.sas.com/publishing/pubcat/chaps/58789.pdf
Carbonate deposits resulting from a microbial process in a solution containing required nutrients for bacterial growth, 0.1M CaCl2, 0.78M urea and 50% seawater (composed of 0.055M Mg2+, no Sr)...
04 May 2015 1,196 9 View
I am looking for someone, who is expert and interested in investigation of caco3 polymorphs formation through microbial activity, for cooperation in writing a research paper (as an co-author). I...
02 March 2015 7,962 3 View
I have the XRD patterns of two samples which mainly contains calcite and aragonite (S1 and S2, see the attachments). How can I just roughly say that S2 has more amount of aragonite than S1?
01 February 2015 1,514 12 View
It is known that the urea will be degraded to NH4+ and CO2 within a hydrolysis process. In higher concentration of urea, [NH4+] increases till the point at which the solution is supersaturated...
01 February 2015 2,887 3 View
I recorded the concentrations of a product during a reaction. There was an enzyme producing bacteria as catalyzer. Then I plotted the concentration changes versus time and fitted a modified...
31 December 2014 9,208 9 View
I analyzed a sample contained calcite using XRD. The pattern attached. It was identified as nitratine by the related software searching the database of XRD patterns. As nitratine is isostructural...
31 December 2014 5,633 10 View
How much a model with: - Model p-value < 0.05 - Lack of fit p-value > 0.1 - R2=0.99, Adj. R2= 0.99, Pred. R2=0.99 - normal probability plot attached (residuals do not follow a straight...
09 October 2014 5,303 2 View
I did a 2-level full factorial design with 3 factors in order to find the significance of each factor and their interactions on a response. After ANOVA on non-transformed response, I found no...
08 September 2014 454 11 View
I did the following full factorial experiments to find the significance of variables and fit model. I analyzed the data using the standard least squares model and generalized linear model (normal...
08 September 2014 2,721 6 View
I did a two-level full factorial design in order to find the significance of three factors (A, B, C) and their interactions on a response (R). Due to interaction between minimum level of A and...
08 September 2014 7,473 5 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View