How can I create .GEM file in SIMION8.0?

01 January 1970 0 3K Report

I wish to create complicated geometries with nonstandard shapes.

I wish to write geometry files for those shapes and want to know how can I write them and load them in the workbench.

Badges
Science topic

More Bharat Singh Rawat's questions See All

What are some methods of making very thin grids?

I am working on gridded ion thrusters.Presently we are using 1mm thick and 100 mm dia disk for beam extraction which has around 1000 1-2mm holes in it. The manufacturing of the grids is a...

09 October 2018 6,945 11 View

How can I define a Plasma in SIMION8.0?

I wish to study the extraction of positive xenon Ions through grids at different voltages from a plasma chamber.How can I define a plasma of a particular temperature in SIMION as I think it can...

07 August 2018 1,673 0 View

I wish to extract data from TRIM about Ionisation recoil.How can I find the .txt file?

I am unable to locate the Ionisation recoil file after the simulation in TRIM. Can anyone help with the issue?

01 January 1970 7,722 0 View

Will water boil in my case where maximum temperature of surface is around 400Degree?

I have to extract heat from a surface by cooling pipes of 6mm diameter with water flow.I wish to know whether the water inside the pipes will boil and cause Nucleate boiling effect as in case of...

01 January 1970 3,097 7 View

How to carry transient analysis in ANSYS?

I have calculated the steady state heat analysis for the Faraday Cup Materiel (Copper) and the maximum temperature reached on the surface is around 400-450 Degree Celsius. Is it safe to operate it...

01 January 1970 7,985 0 View

How to decide how much coating should I keep on the surface of my detector?

How should I decide the optimum amount of graphite coating required for my Faraday Cup detector to reduce my secondary electron emission?.

01 January 1970 3,593 3 View

How can I manually calculate the water flow rate required to cool a cylindrical geometry(Copper) heated by a 10kW beam?

I wish to manually calculate the flow rate of water required to cool a cylindrical cup shaped object which is being heated by 10kW beam? Can anyone tell the equations or methods to calculate the...

01 January 1970 6,804 11 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View